Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello,
I want to use McuBoot so I added CONFIG_BOOTLOADER_MCUBOOT =y to prj.conf.
So t here were a lot of warnings "implicit declaration of function ".
Part of the warning...
I need to use 9160 to drive the Lis2dw12 accelerometer for ST. I found some settings related to this accelerometer in NCS, but I couldn't use it after adding it in IIC, and...
Hi There,
Our peripheral firmware running nrf5 cannot seem to connect properly to our central running NCS 2.4.1 over BLE. We are consciously setting the connection to use...
Hi there,
I have multiple flash partitions defined in pm_static.yml.
I want one specific partition to contain a binary data file so that when I flash the image with J...
I 'm using zephyr to create a custom nrf52832 board .
I 'm using the Devicetree Visual Editor .
Any idea why I can 't select this specific display controller ?
The datasheet...
Dear Nordic Support-Team,
the provided samples in nrf-SDK are great to show how to use several aspects of the nrf Sdk and the devices.
Nevertheless it would be great if...
I am planning to create an application on NCS that can have https://github.com/nrfconnect/sdk-nrf/tree/main/samples/bootloader using CONFIG_SECURE_BOOT=y, But is it possible...
TLDR; Need advice on which wireless communication protocol to use for five nRF52840 dongles within 75 feet of each other. I've never worked with Nordic Semiconductor products...
I'm experiencing an issue with I2C communication between the SEN5X sensor and multiple nRF9160 DK boards. The problem manifests as an crc error during I2C read operations...
In case I run the code from zephyr/samples/bluetooth/broadcast_audio_source, I get following error, when I play audio:
After I stop the audio, the log messages stop...
Hi,
I'm pretty new to Zephyr and I have to figure out how to connect to a NOR flash over SPI. Final application is the implementation of a file system, e.g. littlefs.
...
Hello !
I recently updated our project SDK from 2.6.0 to 2.7.0 and our custom board to HW v2 layout. Everything went almost seemless until I tried to enable sysbuild option...
We created a product using nrf52840. the product is operating well, but it has been confirmed that software reset (0x04) operates in very few times (2weeks per 1time). In...