I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
(nRF Connect SDK, v1.8.0, nRF52840)
I would like to create classic Bluetooth Classic peripheral behavior, the peripheral is not advertising (or advertising without name...
Hi, I created a Zephyr project for board : nRF5340DK_nRF5340_cpuapp . Now, I need to read the Device ID from FICR. I made changes in overlay file as shoen in atached first...
Hi,
I am using SDK 17.1.0 as a host scanner. When I changed the timeout to 0, there was a problem with the connection slave (NRF_ERROR_INVALID_PARAM). I'm pretty sure the...
I'm currently using: - NCS 1.6.1 - Zephyr - NRF52840
I'm using the lwm2m client to read and write to lwm2m objects.
When the device starts for the first time, I store...
Hi,
I downloaded the hello_world_with_mcuboot.zip file that Simon provided in one of the ticket few days ago - Case ID: 283917.
I built hello_world_with_mcuboot project...
Hello,
I would like to know if the application / use case stated below is implementable.
In my application I would like an nrf52840 to communicate with the Bluetooth module...
hi,
In the NUS routine, it is necessary to turn off the peripherals before entering the idle mode to minimize the power consumption, but there is no change after adding...
Hi,
I'm trying the sample fat_fs on the nRF5340 DK
1) It does build, but there is awarning
CMake Warning at D:\nRfConnect\v1.8.0\zephyr\CMakeLists.txt:722 (message)...
On a MCU PCA10040 v2.0.0, I ran the command:
.\nrfjprog.exe -f NRF52 --program .\final_image.hex --verify --reset
Which subsequently caused the board to go into a reset...
I have a Thread bench-top environment set up that includes
One nrf5340dk flashed with the openthread coap_server firmware build and flashed on 1.8 via Visual Code
Two...
Hi
If a bug stop the application to feed the wdt,Is there any way to store 8bytes application data to flash before reset which occurred by wdt?
I find that there is only...
Hi,
I'm having some difficulties understanding how to manage commands in endpoint-specific callbacks. For example, when receiving a "ZB_ZCL_CMD_CONFIG_REPORT" I'm able to...
Hello,
I have a peripheral (nRF51822, S130, using the peer manager) that should be paired/bonded with one or many centrals. I have followed the example ble_app_bms from...
Hi everyone,
I implement nrf5_SDK_17.0.2 ble_app_uart example and I use an android app like nRF_Connect to receive the uart data on my cell phone.
The problem is that...
