Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
Hello,
I am attempting to program to a custom board using VS Code. I am using the Bluetooth beacon advertising example from BLE fundamentals Lesson 2 Exercise 1.
I am...
I am experiencing an issue with my Tenstar nRF52840 Pro Micro board, which utilizes the Adafruit UF2 bootloader. When attempting to flash new firmware by copying a .uf2 file...
Hi my name is Assaf im using Nrf9160 on custom pcb with SDK and toolchain v2.5.2. I made modbus code which works just fine but when im enabeling the MCUBOOT related configuration...
I am working with St7789v driver based RGB565 Display . I have chosen SPI21 configured at 8Mhz and if I send 15 bytes chunk of image bitmaps, I can see the image in the display...
Hi
I notice there is a statement in nRF7002 dts:
I am wondering if I could always use the highest TXP 0x54 for all modulation indices to achieve optimal communication...
I attempted to connect the central device to the peripheral device.
Both sides are custom boards of nrf52832 and both are based on nrfSDK v17.
The log output on central...
When advertising using Coded PHY with the nRF54L, the reception rate is half to one-third compared to 1M PHY, even at short distances (sufficient RSSI). The receiving device...
Hello,
I am using a custom NRF5340 board and trying to run SPIS related code. The issue I am facing is that MISO pin kept low during the complete transaction . My pin configurations...
Hi, I have been getting randomly errors status from pmic measurements including status 64 (trickle timeout, I presume). Do you have any sample code to handle errors as per...
This is a custom board with nRF54L15. I have the following peripherals connected:
I2C30 SDA:P0,02 SCL:P0.03
I2C20 SDA:P1.13 SCL:P1.12
UART00 TX:P2.02 RX:P2.00
I also...
Hello,
Currently designing in the npm1300 into a project and want to understand better the difference between the LDO and the load switch. In the example schematics the...
Hi
Since the Vout setting range is 1V~3.3V, and the datasheet Figure 39 show the dropout voltage is ~60mV(0.06V)
Why datasheet LDO electric spec. show the VIN need larger...
Folks,
We have been developing a product to use the nrf51840 Dongle. Idea being to solder it to a mother board and as it's pre certified we don't have to go through RF certification...
Hello, I'm building the sample Measure battery voltage on a custom board, and I have an error voltage: setup: -134 at runtime. The overlay file is configure as explained in...
