Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Dear Sir,
I got error like '[00:01:44.604,858] <error> app: ERROR 1813 [Unknown error code] at KGJ`hó@h:536871936 PC at: 0x0001505C' and I can't where did it happen, I...
Is SD340 v7.0.1 compatible with nRF SDK 17.1.0? https://www.thisisant.com/developer/components/nrf52832/#tab_protocol_stacks_tab
Reason I ask is on the InfoCenter there...
Hi all,
I'm working on the nrf5340 with a modified mesh light sample and nrf connect sdk 1.7.1
I'm measuring from P0.28 which is also LED1 to the GND.
After programming...
Hello,
I am using nRF5 SDK for Thread v4.1 for thread implementation using nRF52840 SOC. I have used mqtt-sn sleepy publisher as my base example to develop my software....
Hello,
I am struggling trying to make this sample work on my board. I changed my prj.conf file with these lines:
And looking at other questions I discovered that sometimes...
Hi,
Is there any way to make app_usbd_audio_class_rx_start(...) complete the data transfer within the same context, rather than defer to user event
APP_USBD_AUDIO_USER_EVT_RX_DONE...
We have been using nrf connect installers 3.3.0 and now 3.7.0. We have recently seen issues with new users encountering this error when installing 3.7.0. Are there any solutions...
Hi,
I started to evaluate the Instaburst feature. I use light_switch_client example, but I am unable to provision the device once I enable this feature.
Below are the...
We are in the early phase of architecting a product that uses BLE and a proprietary RF protocol using the nRF52840 and are considering the addition of the nRF21540. In sifting...
I am currently trying to create a simple BLE observer which listens to advertisement broadcasts from a specific device (given via address). I attached the source code below...
Hi,
SDK - 17.1.0
I want to store my sensor data to the internal flash memory of nRF52810 for a long time. I have some questions here:
The data sheet says the flash...
Hello,
Few years ago I developed an application for nRF52832 (BMD-300). Now our customer wants to port the application to nRF52810 (BMD-330) as BMD-300 is not available...
When I'm trying to use arm_rfft_fast_init_f32 function from the CMSIS DSP library it seems to work with all sizes but 128. When the function is invoked with the size 128 it...
Hello,
Using a ZR device with nRF Connect 1.5.1.
I am wondering how to stop steering mode in a ZR device (e.g. if user requests an "abort").
It is started with bdb_start_top_level_commissioning...
Hi Dears:
When I downloaded and installed nRF Connect v3.3.1, the following screen appeared.
I remember when there was a drop-down box to select the BLE component. ...
