I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
How is it possible to run a DTM Test on a custom board using the nRF Connect Tool?
I am able to run it successfully with 2 DK boards, but I need to run it on my custom PCB...
1. I had done the pairing without any authentication but now I want to do it with the authentication with an authentication key.
2. please provide some sample code regarding...
Hello DevZoners, I hope you are all doing great!
I'm struggling to understand how this works.
I've been following the NCS Tutorial part 2 to implement the PWM peripheral...
Hi,
I am working on nrf5340. I would like to change the TX and RX default pin of uart0 to <33> and <32>, I modified the file "nrf5340_cpuapp_common.dts" as below.
The...
I've been develop the other MCU;s DFU driver for the nrf52832 recently, and I ran into several problems.
The first I show you my DFU step in the RTL8720( Be the central...
Hi there!
I'm using the nRF Connect SDK with the VScode extension for developing an application for the nRF9160DK. I've taken the lwm2m_client sample as base and rewrote...
I'm struggling to get buttonless DFU to work with FreeRTOS. I've gotten buttonless DFU sample to run on the hardware. I also have FreeRTOS running on the hardware. However...
Hi team,
Environment :
nrf52840
s140
1.How to enable the second regulator stage REG1 use of DC-DC converter ?
2.What is the default configuration HFCLK and how to...
Hi Everyone,
Wanted to test the NFC library provided by the nrfxlib on the nrf5340DK. Added the following config file:
Resulted in:
How could I check the reason...
Hi,
I have added a nrf-9160 DK device to nrf cloud and it is always is shown as disconnected (disconnect reason MQTT_KEEP_ALINE_TIMEOUT ).
Previously i have updated the...
Hi
We are using a nrf52840 on a custom board.
The board always worked fine.
Flashing is done with :
- SEGGER J-Link EFM32GG-STK3700
- nrfjprog version: 10.15.0...
I am seeing the error below when I try to launch a debug session inside the IAR IDE.
I am working on the nRF52840DK and am seeing this error on the DFU example in the...
I'm Using sim card which support both LTE and NB-IoT. In some areas i can't use LTE-M and in that case i need to switch it to NB-IoT. I referred and there is fallback method...
I am using the Ceedling framework for unit testing my firmware. This has qorked quite well. But now I wanted to use the section variables to decouple my code a bit more. And...
Hi. I would like to know how to do a DFU over UART using a custom desktop application (without using nrfutil command nor nRF Connect app). What would be the UART protocol...
