I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hello,
Basically I'm using NCS SDK (1.7.0 - see Generated Info in the end) and Zephyr.
The board I'm adventuring on is the nRF52840 DK.
In the project, I have 1 main...
Dear Team ,
when I am debugging my code then work properly work but when we upload another example .after some time again i try to debug my previous code in this time debugging...
I am trying to convert the Zephyr gsm_modem sample project to C++. If I include `gsm.c` without using `extern "C"{}` I get this error: ` undefined reference to gsm_ppp_start...
I have an https connection (sending json) that works fine when the response is less 2k. But for responses (from the server) that are over 2048 bytes, recv returns 0 bytes...
Hi,
Our program is now based on ble_app_uart example, and we want to add the 'wake up on NFC' feature. I checked the 'wake up on NFC' example and related posts sending via...
Link: https://www.nordicsemi.com/Products/Development-software/nRF5-SDK/Download#infotabs
Clicking "Download files" at the bottom, eg with SDK 7.1.0 selected causes a...
Hi,
I want to configure the bootloader (MCUBoot on a nrf9160) to reject a new firmware image update if the new image is not suitable for the current hardware (e.g. multiple...
Hi Dev team,
I have my Thingy91 deployed and running. I wanted to know how could I locate the base station that my device is connected to. I have the information of MCC...
Hello, i'am trying to display data on my sensor Bme280 aka (temp, humidity and pression but the build is successful and the jlink is well connected the wiring is like below...
Hi,
I was using nRF Connect with all applications listed. But after installing nrfutil from git, the application all disappeared. I uninstalled nRF Connect and reinstall...
Hi, I'm attempting to use an nRF21540 to boost the range of a BLE Beacon, and I'm running into a lot of trouble getting the Eval/Dev Kit set up. First off, is there any documentation...
Is there an nRF Connect mesh sensor example. The light on/off example is great, but very simple. There is an nRF5-SDK-for-Mesh example. Are nRF5-SDK and nRF Connect compatible...
Hi to everyone,
I'm evaluating an application consisting of a bluetooth mesh where each node sends a status message to the others.
The area where the nodes will be deployed...
Hi,
We need to know the list of models (like health, configuration, lighting, sensor, generic on/off) in nCS sdk 1.7.0
can you please share inputs
thank you,
To update the Application, it is necessary to implement the update via CAN bus. Below is the hardware part, we use a CAN-SPI chip to access the bus.
We´ra using Microchip...
