Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
On a dice projet based on NRF52810. Sometime when I plug the battery charger the firmware crash at address 0x18808 and the call stack is empty !
This address is in...
Hello,
Can anyone please share some reference example for implementation code for central device which scan for available device.
I am using nrf52840.
Thank you
I have successfully installed the blinky example app on my new Nordic nrf 52840 Dongle - so that's good! :)
However, some things are not clear to me - so I would like some...
Hi,
I'm using nRF5_SDK_17.0.2_d674dde\examples\ble_central_and_peripheral\experimental\ble_app_multirole_lesc\pca10040 & pca10056
Wants to send data packet over switch...
Hello,
I am trying to implement ble_dfu service into an existing project. The problem is I can not find an example in the SDK. I need to find out which macros to copy-paste...
Hello All,
I have a specific requirement to run 2 different functionalities from the same HEX file. Can someone suggest is there any means of special logic in the nRF52...
I have successfully ported the fatfs file system to my application code, but copying the files is very slow. I'm trying to modify the mass_storage.c file,follwing is my code...
I have two nRF52832 feather boards. Trying to set a simple connection between them so that board 1 sends beacons and board 2 receive them. Every few minutes, board 1 pair...
Greetings,
I am trying to run the scan_adv example from the samples. I am using the nRF52832 kit and SEGGER for running this sample. However, I face the error mentioned...
Hi everyone,
I am following this video step by step to create my custom board configuration https://www.youtube.com/watch?v=KSivO9Cf1TE&t=474s .
I follow every steps but...
Hi all,
My project can be built and run correctly on NRF SDK 1.5.0,
after updated to SDK 1.6.1 and rebuild, it failed and messages below:
Is there any idea for this...
After installing nrfConnect SDK v1.6.1 on MacOS ( Big Sur 11.5.1 ) using Toolchain Manager, I can't find nrfjprog.
When I try and run nfrjprog in Terminal, I get: "zsh:...
Because some IOS devices support up to 185 Bytes MTU, Android phones 247.. is there
any possiblitly wow the Application Core NRF53 can retrieve the current MTU Size from...
Hi
I am working on a nRF52840 using Zephyr as OS.
I have setup some control GPIO pins in the device tree (se below). This works fine from the application. I can access...
