I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
I would like to sample a digital IO input from two IO's into the processor internal memory incrementally per every rising or falling edge of each of the signals.
Is there...
Trying to do ADV_DIRECT_IND advertisement.
We are trying to do the following advertisements
// ADV_IND Scannable and Connectable
// ADV_DIRECT_IND - Connectable...
I recently purchased an nRF52832 (XL52832-D01) for a wearables power management project. To test the module I flashed the basic blinky (zephyr). I'm using a ST-Link V2 as...
Hi
Brand new nRF52840-DK (PCA10056 rev 3.0.3, serial 1050245467, sticker on PCB). Never worked.
J-Link OB firmware update fails every time with: "Sending firmware data...
Hello! I am having troubles with my custom board using BL5340 from Ezurio. I have tried to flash it via my nrf5340 Audio DK but realized it doesnt support external Flashing...
Hi,
I am trying to set up a secure boot chain on nRF54L15dk with NCS 3.2.3 and an upgradable bootloader .
My intended boot chain is:
B0 / NSIB
S0 / S1 for the second...
Hello,
I would like to implement Device Firmware Update (DFU) over NFC.
Is this supported, and is there any recommended way to implement it? Are there any examples, reference...
I have two nRF52840DK boards that I was working with recently.
PCA10056 3.0.2 2024.33
I flashed one board with a BLE peripheral device code from the nRF connect sample...
Hello,
I'm using dmic module for sampling audio data from microphone. Recently I updated NCS to 3.2.2 and I started observing the following log: "Failed to allocate buffer...
After an update recently with the nRF Connect for VSCode Extension, it's been unable to find where my nRF Connect SDK is located when choosing a build configuration. It used...
Hi,
We are migrating from NRF52840 to NRF54L15 (QFN48).
I am using nrf54l15-qfaa-reference-layout-0_8 as reference but really struggle to understand some design choices...
Environment:
Board: nRF54L15DK ( nrf54l15dk/nrf54l15/ cpuapp )
NCS Version: v3.1.0
Zephyr OS: v3.7.99 (NCS fork) NOTE: I am building this over peripheral uart example...
Hi,
I am developing with NCS 3.0. In my application, I need to use MD5 to calculate a signature. Following Nordic AI's guidance, I enabled CONFIG_PSA_WANT_ALG_MD5=y in prj...
