I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello, I am currently using the TWI in non-blocking mode, however I frequently run into the issue where the code gets stuck on nrf_drv_twi_tx. function at the return result...
Hello,
i have created custom BLE service/characteristic using this ling https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial
So, here i am able to transmitting...
Hi,
I tried running the "chat" example on two NRF52833DK boards, one as a sender sending a "Hello World" message every 500 milliseconds, the other as a receiver, and found...
Dear Support
I try to use Watchdog on nRF9160 DK.
I found the sample ..\v1.5.1\zephyr\samples\drivers\watchdog
From there I add to my prj.conf
CONFIG_WATCHDOG=y CONFIG_WDT_LOG_LEVEL_DBG...
Hi,
I wanted nRF5340 capable of reporting the VDD under-voltage event causing a pin reset through a dedicated voltage monitoring IC. For this reason I put a Flip-Flop for...
I am currently experimenting with moving my request for PSM mode into the "lte_lc_init" routine so that it is configured before the modem is moved to Normal mode.
With...
Hi!
I have previously tested connecting the nRF9160-DK to an external MCU to act as an Serial LTE Modem as per the application description. And it worked
fine. Since then...
Hello.
I use nrf9160 and download ota with aws.
After my board download successfull and return event FOTA_DOWNLOAD_EVT_FINISHED, I do system(0) to reboot.
But it can...
Hello,
what is the raw frame to get a good NRF Temperature Service UUID BLE ?
I didn't get custom data (temperature), just the service uuid 0x1809
Here is my raw frame...
Hi
Since a recent Android security update, I am experiencing issues with my 'Just Works' device based on NRF52832. Prior to this Android update, once paired, I would receive...
I am trying to connect ,disconnect and connect using nRF dev kit with one of the BLE product. (using PC-BLE-DRIVER-PY)
Steps:
1) Open driver connection:
self ...
hello Nordic
i am using nrf52832 soc, sdk 16.0, s132 v7.01
my app requires the s132
i am trying to understand the bootloader issue, not so successful on that unfortunately...
We are developing a product based on nrf52840. The product will always be configured as a BLE peripheral. We need to be able to use OTA for both SoftDevice & Application code...
