I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I'm aware that the nRF CLI tools are not yet ported to AArch64 so they don't work natively on Apple Silicon. Normally rosetta 2 is fine, but nrfjprog is not compatible with...
working with nrf52832, sdk 16.0 s132 v7.01
in the uart example i get to this place in the code :
i get a pin toggle which makes my system do some unwanted things...
Hi,
I have a ARM based Linux host CPU connect to MDBT42Q-U(nRF52832).
But I cannot control it by BlueZ:
```
root@OpenWrt:/# btattach -B /dev/ttyMSM1 -P h4 & root...
Hello,
After some weeks of inactivity and moving my desk to an other address, the nRF connect application is not running and show a white screen for all applications except...
Just checking in, I am recently starting to develop cellular communication and looking to develop on the nRF9160. I have been in nRF52 space and with that I develop inside...
Hi, I'm using nrf52840 DK. In my project I want to receive audio from microphone (analog) and stream it to bluetooth headphones. Is there any possible way to do it? Any help...
Hi,
I have been working with a nRF52840 DK up until now, but I need to change and move to a nRF52833 DK. I wanted to adapt my code as they can both use the softdevice I...
Hi all
I'm working on a project based on the nRF52 chip and I'm encountering
If the system runs out of battery or no buttons are pressed within a timeout the system has...
Hello
I made an application on the nRF52 sdk, which works correctly.
Now I want to add the ability to update the firmware via OTA bluetooth.
I followed the instructions...
1. Using Zephyr, trying to config SPI_3 of nrf9160 more than 1MHz for flash interface.
2. Ending up in faults.
3. We need to configure SPI_3 as master with freq > 2MHz...
hello!
im using sdk 17.0.2 with softdevice s112 in our customized board as i want to work for long range mode,so i need extended advertisement ie no available in s112 so...
Hi team.
we are developing project using nrf52 mesh sdk including 1 port nRF52840 and other nrf52 devices. we are finishing dfu mesh for devices.
The nRF52840 gateway...
Hi,
I'm developing a multi-scene application by reference to the "Light switch" example in nRF SDK for Mesh 5.0. The first screenshot show my Elements & Models structrue...
I would like to use the USB dongle with the Openthread CLI example (and eventually an open thread app) as the SDK is just too big and overpowered for my prototypes, I would...
Hello,
I would like to obtain some information on the possible substitutes for the nRF51822 (BGA Packaging).
I received notification that right now only the final orders...
