I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I'm working on getting PSM mode in LTE-M working so I can go to very low current operation between transmits to the cloud. I have things working pretty well, but...
We are using over own server that host multiple apis for different functionalities.
I am able to make http post requests to all of them individually and everything works...
Hi
I am about to make an application where a device is sending a sync pulse (60Hz) out to a number of Host's.
when I test with a device and a host, I get approx. 1.22ms...
I am having trouble finding a commercially available BLE 5 dongle that I can be confident will support Linux BlueZ as well as the LE 2M PHY. I would like to know if I can...
Hello,
I have an evaluation board with a nRF52832 chip on it. I added some code to ble_app_uart example and flashed it on the evaluation board.
Here is my problem: I added...
Hi,
I'm trying to use BLE to send data to a computer from the NRF52840 DK. So far I'm trying to get nrf_sdh_enable_request() to compile without errors, but I keep getting...
Hello,
I have both an installation of NCS v1.5.0 from Toolchain Manager (TM) and from the Getting Started Assistant (GSA) on Macbook running macOS High Sierra. The TM SDK...
Hi
I am using nRF9160DK board and need transmit gps data to web site, I am trying with udp but have problems with that, I would like to know what protocol use asset_tracker...
Hello,
at the moment I am trying to implement a counter that increments every 1ms. I wrote the following code for this:
Regarding to the documentation ( https://infocenter...
Hi there,
I am running a custom board based on the nRF5340-DK. It's a minimal board, notably with both oscillators
It seems to behave itself with low-rate BLE use-cases...
Hi.
I'm having trouble flashing my Thingy:91 with the nRF9160DK as a debug probe.
The DK is set to 1.8V, I have a 10pin JTAG cable connected to the debug out of the DK...
What is the UICR setting in nrf51822,S110? Currently, when I develop with nrf51822,S110, the UICR area is 0xFF. I want to set the UICR as follows, is there any way to set...
Hi,
I am using multiple channels of SAADC for monitoring some data and then I send every 20 samples of adc in a 32 packet through Radio/BLE using the esb_ptx example and...
