Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello dear,
I am installing Embedded Studio on OSX (Catalina), and I following the nRF Connect step... all goes fine, but when I try to use "Open nRF Connect SDK Project...
I'm trying to see debugging info with nrf51 dongle.
As far as I can tell I just need to use:
#define NRF_LOG_MODULE_NAME "APP"
#include "nrf_log.h"
#include "nrf_log_ctrl...
On a nRF5340 DK the sample ncs/zephyr/samples/subsys/usb/cdc_acm runs fine. However, if I add "CONFIG_NO_OPTIMIZATIONS=y" to prj.conf I get faults (see below). Any ideas why...
Hi,
I am preparing Windows desktop application which will use nrfutil for DFU of the products (containing secure dfu bootloader). I tested nrfutil v6.1.0, v6.0.1 and even...
Hii guys,
I am trying to establish communication between two nrf52 module.
My application is as following
1. I need a central device which can work as master and remains...
Hello, I am stuck initalising both TWIM and UARTE. I am focusing on the TWI Scanner example but using TWIM instead of TWI. No matter what I do I cannot get past the initalisation...
Hi,
How can I increase TX Power in nRF Connect SDK ?
I have already followed the hci_pwr_ctrl example, but I got the error "Read Tx power err: -5 reason 0x00" in get_tx_power...
We use nrf connect sdk under linux.
I need to control tx power to be able to adjust working range.
I take example from zephyr/samples/bluetooth/hci_pwr_ctrl
Add segger_rtt...
Hello,
I recently cloned NCS v1.5.0-rc1 using west init -m https://github.com/nrfconnect/sdk-nrf.git followed by git checkout v1.5.0-rc1 and then west update in the nrf...
Hello,
I'm a beginner and I'm a bit lost. It's rather complex to understand everything there is to know. So I ask a lot of questions, sorry.
I was advised to use the lib...
Hello,
We are not finding RFX2401C on the market for sale and we are looking for a PA for the NRF24L01+.
We found the alternative RFX2411, is it safe to assume we can...
Dear community
I'm developing BLE secure firmware on an event-driven proprietary RTOS.
According to the documentation of nrf_ble_lesc_request_handler() , it is required...
Is the BLE connectivity offered by the nRF52840 (upon which the Arduino Nano 33 BLE is based, I think) DIRECTIONAL? Should the board be oriented in any particular way to maximize...
