I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi, my BLE application on nRF52832 is designed to select two mode to operate with 3 position slide switch when power on like ON(Mode 1) - OFF - ON(Mode 2).
At Mode 1 position...
Hello.
I'm using nrf52840 to sample the voltage from the wireless board and then send the data to the PC via Bluetooth.
With the help of DevZone, it was able to construct...
Hi,
I have downloaded and installed nRF Connect for desktop - Bluetooth Low Energy. Now I want it to operate as a peripheral that can send connectable advertising packets...
I'm having an odd issue with libUARTe sending a TX buffer twice.
I have a custom board using an nRF52832 running an application based on SDK 15.3.0. The libUARTe code was...
Doing development on nRF52 DK board using buttonless DFU example and SDK 17.0.2. Running SES on Win10 and gnu compiler.
I've set up a 1 mS timer to run timing in my main...
I am using the ble_app_uart in combination with the f_storage example to write data to the flash memory. A issue which arises is that, when a softdevice is enabled, the nrf_fstorage_nvmc...
I am using Mesh SDK v4.2.0 and my goal is to get the device MAC from the UUID that is available from p_evt->params.unprov.device_uuid available on the prov_evt_handler callback...
I guess this should be obvious, but I still have to ask. What do XRFTEST RX and TX modes actually do? I've read the documentation and it "feels" like they command the transceiver...
Hello
It seems that we had a crash during execution of nrf_bootloader_fw_activate() in an added sub function where we program an externally connected MCU and the bootloader...
Dear Sir,
I'm use 2 nrf52840 chips to test sensitivity by nRF-DTM-1.0 tool.
I find out it's work on 1M and 2M but S8 and S2 can work.
The PER can't get 0% when I only...
Hi all,
I am developing BLE firmware to send and receive data between the development kit PCA10100 and nRFConnect App Desktop.
I'd like to notify the client (the App)...
Hi all, I am using SPIM with dma list triggered by gpiote. A gpio low-to-high event starts spim reading, and it works fine. However, I need to read different length at different...
Hi,
I am getting following problems while executing ble_gls example.
1.device gets disconnected immediately after connecting
2.getting timed out error problem
Kit...
Hello DevZone Developers,
Presently, I am trying to find H/W which support BT 5.1 Direction Finding.
I came across this , where it is mentioned that "Nordic Semiconductor...
