Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello,
I want to give user defined hard-coded OOB Number in this example for generic on-off Client-Server code, for provisioning both client and server node ( nrf52 DK ...
Hi,
We use mdbt42v(nrf52832) to design a custom board and we encounter a strange issue.
We use ain2(P0.04) to measure a Variable Resistor value, the code working fine...
Hi,
I am using an NRF52832 device (Peripheral) and I have a requirement to transmit around 4kb of data every 100 ms to a Central.
Can you recommend the correct example...
Hi,
I tried building both with cmd line and SES but I get always this error:
/usr/local/bin/cmake -GNinja -DBOARD=thingy91_nrf9160ns -DBOARD_DIR=/Users/dariofanciullo...
Hi,
I am using nrf52832 to connect 500 nrf52810, among which NRF52832 is central and nrf52810 is peripheral.
How should I do for nrf52832 based on SDK 16.0.0.
Hi,
I want to program my chip nRF51822 ( https://www.waveshare.com/wiki/NRF51822_Eval_Kit ) using the KEIL tool and the ULINK2.
When I try to program the chip KEIL show...
Hi,
I've encountered a problem with opening a project in Segger Studio. I have recently moved to 1.3.0 tag and I am working with Thingy:91 (so I basically open nrf9160 samples...
I'm doing a Nordic example named "Nordic UART Service Client" ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v17.0.0%2Fble_sdk_app_blinky.html )
The steps...
Hi ,
I ran the example "zephyr\samples\bluetooth\scan_adv" on the nRF9160 dk kit .
It says the following error
"
2020-07-16T02:22:00.682Z DEBUG modem << *****...
Hi, everyone
A LPN ( Node-LP ) had selected one of nodes as its friend ( Node-F0 ), if Node-F0 is taken away, will the Node-LP automatically reselect other node as its...
I read somewhere for new project we should use nrfx driver because in future old nrf_drivers will not be support and improve. All examples in sdk15.3 as I understand used...
Hi All,
I am trying to implement a battery level reading app using NRF52840 DK. It seems I am receiving a timeout from saadc.
In order to run on the Lithium battery, should...
Hi,
I programmed two thingy:91 to return RSRP and RSRQ to a server. On is running with LTE-M and the other with NB-IoT.
I found something that seems strange : +CESQ: 99...
Hey everyone, I'm trying to use the QSPI module (again) to interface to RAM, not FLASH. I'm not really sure if this is possible, but we'll get there. Right now I can't get...
I've been tested for BT SIG however have met error which sent 0xc000 and got 0xc000. I expected to receive 0x8xxx. Command is LETestEnd.
I tested with nRF51822 customer board...
