Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi All,
My one of the old application is based on SDK11 and i found some issue data corruption with FDS module. After reading some post here regarding FDS issues and also...
Hello,
I am trying to evaluate the Channel Selection Algorithms (CSA) 1 and 2. From what I found on here, CSA 2 is enabled by default in SoftDevice stack, could you please...
Hello everyone. I want to create project from stracth for nRF52832. I use nRF52 DK. I couldn't find any tutorial for this. I create new project under nRF5 SDK 16.0 and specified...
I am using BT840F module from Fanstel which is based on nRF52840.
Currently I am having two EV-BT840 (Evaluation kit for BT840). I have modified 'pca10056.h' as per my board...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hello Devzone,
I've been working on a system to set notifications on time ready for transmission.
The client sends a WWR package to my peripheral and I want my peripheral...
Hello,
Currently, I'm trying to flash my custom board that has nRF52832 with an uart application that I integrated buttonless DFU. I'm running into a problem where when...
1.nrf9160 is there an RF calibration parameter at the factory?
2. If there are calibration parameters, does burning mfw_nrf9160_1.2.0.zip firmware affect the calibration...
I have two devices here, So I combined three HEX files and burned them with JLink, and they don't behave the same. One starts the application normally, and one is always in...
I am using a custom board with nRF8001, where I use external interrupt from the RDYN pin to let MCU know BLE has an event. MCU can recognize these events and change the associated...
Hi,
I added the feature of the 'buttonless dfu' to the 'hrs freertos' using the SDK v15.3.0.
After programmed the built image to the EV board PCA10040, it could run normally...
Hi
I have 2 customised board with nrf52832, I wanted to communicate between 2 devices. Like to send commands like turn on/off LED from my one board to on/off LED on my second...
hi
i want to use iic in my project ,and i add iic func to my project refrence project twi_sensor.
the code of iic like this：
I call the api in the main
then...
Hello
I would like to use the extended advertisement feature of BLE 5 but I have several questions: 1. If I want to broadcast data in "extended advertisement" messages ...
