Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hey all,
So I am a beginner and haven't work with this environment a lot. I use SES to debug and upload application to the nrf9160. I can allready upload some basic application...
Hello, I have three nrf52840 development boards and one pcb that I made myself using nrf52840. I want to find the location of my pcb with a demo using these development boards...
Hello,
Softdevice: 7.0.1, SDK: 16.0, Device: nRF52840
In the production, we want to save time programming the devices. So I'm using following command to combine bootloader...
Setup : I am using android-ble-library for my android app. I am using modified blinky example on embedded side. I have tried following implementation on android app:
I...
I have two nrf51822 devices, one running s110, the other s120. The s110 device reads ADC values every 20ms, and if they changed from the last reading it sends a notification...
Hello,
The following define is present in file nrf_sdm.h, SDK 17.0.2:
#define SD_FLASH_SIZE 0x26000
I think it's wrong, it shall be 0x27000. But it's maybe not used...
I am working with a IC that requires SPI clocks to be synchronized (in phase) with its system clock. Currently the IC's clock source is connected to one of the nRF52's GPIO...
problem: in BLE data length negotiation , In the response from slave tx doesnt go above 216 , and rx doesnot go above 54 .
s140
Experimental UDP example - sdk v16.0 (...
Hi.
I'm pretty new with SEGGER Embedded Studio and with nRF9160 dk.
I would to receive time with NTP serveur but I'm lost.
I don't know what to use. if it is better...
Hi, I am working on nrf52840 and I am trying to enable the repeated pairing attempt protection. (PM_RA_PROTECTION) After enabling the module I can see the logs telling me...
Hi All,
I want to create a Thread network with multiple OTBRs, which is based on two nRF52840 run Thread RCP hex provided by Nordic SDK.
I created the thread network by...
Hi there,
I would like to set my dongle into DFU mode from software, I am using the USB-CDC-ACM class, and the softdevice as a central device.
Ideally I would send a...
Hello,
in our project we have a nRF52840DK as central and a nRF52832 chip on a custom board as peripheral. The software on the nRF52840DK is based on the ble_app_uart_c...
Hello
I use mpu6050 and I want to use a 'Complementary Filter' to get the angle of the X, Y, and Z axes.
Applying this filter to the value of mpu6050 seems to reduce...
Dear all,
Greetings!!!
I am using the NRF24LE1E module. I want to pair my device with host using a button. Button is available on device side. Please help me to do it...
