Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello,
I am working on a project that uses Azure as a cloud IoT provider and the NRF9160 as a gateway-like device which is supposed to make simultaneous connections to up...
Hi,
Just wondering if it is possible to configure the UICR Customer registers after erasing and flashing/programming the nrf52832. The hex file used to program the device...
Hi Team,
I wonder the operating system which has been ported on nRF52840 DK, I found multiple IoT OS what nRF52840 supports like ARM mbed, Zephyr, Contiki, etc. But can...
Using NCS 1.3.1.
Why is nrfx_spim_xfer() asserting when using NRFX_SPIM_FLAG_HOLD_XFER flag and a ss_pin ?
When not using a ss_pin in the spi config but configuring with...
HI,
I was trying to update firmware on thingy 91 using MCU bootloader. Now when I trying to upload again it is keep showing one error.
Error while probing devices: Error...
Hello,
I'm using nRF52832 and SKY66112-11 PA/LNA connected to increase the range. I'm using nRF5 SDK 17.0.2 and nRF5 SDK for mesh 4.2.0
I followed this guide to use PA...
Hello everyone,
I'm programming for nRF52833, using SDK17. When I program for scanning filter (SCAN_NAME_FILTER and SCAN_UUID_FILTER) and debug, I got these errors. I don...
I have a ST link V2 with swd interface support. For one of our existing projects ( custom board ), we want to examine the current consumption of BMD-350 ( NRF52832 ). Hence...
I am currently tasked with programming the NRF52810 to boot up upon a button press and then sit and wait for further button presses to trigger various functionality including...
Good afternoon
According to the project requirements, two keys were added to the compiler settings for stricter project verification:
-Wsign-conversion - Checking for...
Hello,
I have tested the ADC+UART in nRF52 BLE module,
and now thanks to help of this community, I can get the ADC value with UART communication.
Sorry for so many questions...
Hello I have an issue with the exit.c file, Eclipse tells me: exit.c:(.text.exit+0x16): undefined reference to `_exit' I do understand that this is a linkage problem that...
Hello Sir or ma'am
I am trying to load CPP SDK on my nrf52840 DK, But whenever I compile my code it through the error like this," vector: No such file or directory". Now...
Hi, all.
I'm using nRF52832 Software Development Kit, PCA10040, S132.
Using the 'ble_app_uart_c' example, I am studying to connect with my beacons and read data.
I...
Hi,
When evaluated under the following conditions, there was Out of band spurious@325MHz~403MHz (See the following Results ).
Does nRF52832 has spurious(-50dBm~-60dBm...
