Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
I am new to nordic thingy:91 I have a hardware of nordic thingy:9160 ( PCA20035 ), but I do NOT have nRF connect DK (PCA10090).
I am planing to perform development...
Hi team, the problem is the following:
i use secure bootloader project from examples of SDK, when i try to replace NRF_LOG_INFO() statement to printf() and try to debug...
SDK: 15.3.0 Example: ble_app_multirole_lesc DeviceA: EYSHJNZWZ (nRF52832) DeviceB: Smartphone (iPhone)
DeviceA has a bonding key. DeviceB does not have a bonding key. When...
Hello, I am using the PCA10056 to program a nrf52811 chip on a custom board with SDK 15.3.0. I'm using the example ble_app_blinky_pca10056_s140 on SEGGER Embedded Studio I...
Hi there~
I want to install and run my own nrfutil on my pc run with windows 10, but I cannot get throw it.
After generate the exe file, nrfutil outputs some error.
...
Hi,
I am trying to build an "asset tracking" application in Windows 10 using power shell, but it failed.
Please find the logs below and direct me to the correct path....
HI,
I am trying to load the Asset tracking project in segger embedded studio, but it is giving the following error:
Segger Embedded Studio Version: " SEGGER Embedded...
I'm looking at reference schematic/layouts for the NRF52840 and fail to see how the PCB antennas are 50 ohms. (I understand that it's frequency dependent, and that resonant...
Hi,
I'm doing power measurements for nRF52-DK (SOC nRf52832) and for nRF52840-DK. I'm able to measure reasonable figures from the external supply connector (P21) of nRF52840...
Hello,
I was trying to open assert tracker application on MAC os, in segger studio v4.18.
However, after I open the "Open nrf connect SDK project.." and filled out the...
Hi,
We're seeing DFU issues on iOS that we're not seeing on Android. To make things simpler I've reproduced the problem with pca10040 and nrfconnect for iOS.
I'm using...
Dear support,
I am experiencing an issue while using the SPIS peripheral. The issue seems to be the same one as https://devzone.nordicsemi.com/f/nordic-q-a/33727/new-in...
Hi,
We use the ECB peripheral to encrypt and decrypt data with a proprietary driver implementation (which is not that different from the one in the SDK). It is working fine...
