Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I try to develop a fix that should allow me to use the pc-ble-driver to receive scan responses (see https://devzone.nordicsemi.com/f/nordic-q-a/50082/pc-ble-driver-no...
I have one doubt that why there is elements or models in Bluetooth, it can be simple as sending messages and then translate them into useful work, in this single element and...
hello,
inorder to send a string over ble from a slave to master or master to slave what is to be done??
is there any function for us to pass the string??
I want to understand the meaning of "standard drive, low frequency" GPIO pins. The datasheet mentions to use these pins for frequencies below 10 KHz. Does this limitation...
HI
I have to sending a sequence of 768(96 bytes) bits to program a custom piece of hardware on a single data line. Initially the line is low for 500ns and then each bit...
Hello. I'm testing ESB examples with nrf52832. Want to understand which max speed I can reach with that protocol? Some devzone info says that 1.8mbps can be reached. But among...
The assumption that `fds_record_find` returns records for NOT CHANGING file_id and record_key in the same order they have been written IS WRONG. The documentation sub-section...
Hello everyone,
we are developing a bluetooth application based on the relay example included in SDK 14.0.0. We have already developed our own services and characteristics...
We are working on a combination 52840/9160 board, and after having much success with most software components, have run into a roadblock with the more complex Bluetooth samples...
I am trying to create a custom board file in the ncs/zepher/boards directory for our nRF9160.
If I copy the nrf9160_pca10090 directory to a new nam eg. nrf9160_newboard...
I am using NSDK 15.3, MeshSDK 3.2.0, SoftDevice 6.1.1 and nRF52840 DKs.
Hello, I have followed the documentation for the DFU over mesh here and successfully upgraded a board...
Hi, 1. How soon a DK or something like that with an array of antenna to support the direction finding capability introduced in Bluetooth 5.1 will be available?
2. Provided...
Hi!
I am trying to use serial port library with Free RTOS (SDK 15.3). I created a read task but when I try to read, the function does sometimes receive wrong bytes. I also...
So I am trying to store a few configuration parameters in flash. I am using nrf_fstorage for that. so before storing the parameters, I am erasing the flash but, it hangs at...
I am using the chip NRF52840 ,the board is powed by a battery, and I program the firmware by using the JLINK,then I unplug the JLINK and waiting the system to go into sleep...
