Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
When running the unit tests for Mesh SDK 3.1.0 I get the following failures.
83/92 Test #83: generic_dtt_client ...............***Failed 0.00 sec
From the log I...
Dear DevZone,
I'm new to the nRF52-DK and Nordic in general. I'm trying to set up an nRF52-DK to use with nRF Sniffer, and not having any success.
I have tried following...
Hello!
I want to ask about read operation on nrf51822.
In your examples, as I understand, BT stack handles Read Request automatically and then sends Read Response. The value...
Hello,
I am beginner for bluetooth technology and have very interesting to this technology
I have developed new board (4 pcs) for nrf 52832 and soldered all parts from...
Hello.
Please teach me how to turn on DEBUG flag on Segger Embeddid Studio.
Environment: SDK 15.2.0 and SEGGER Embedded Studio Release 4.10a Build 2018110203.37618 Linux...
Hi I'm facing problem while programming my custom nrf52832 board (It might be issue with flash/ROM setting) its saying this hex file has a data in softdevice region . I'm...
Is nrF52840 VDDH pin only used for REG0 LDO/DCDC regulator output to generate VDD power for the GPIO circuitry?
or is VDDH power used to power some other internal circuits...
Is there a way to access the Gazell heartbeat timer? Ideally I would have a callback to my application when the heartbeat occurs. The main motivation for this would be to...
Hi,
What I did:
Already connected the custom board with nrf52832 chip on pc with python
Already receiving data from the board
I want to have the python code that...
The GPS antenna just fell off the board. Seems like the part has a cold solder joint. This led me thinking that the LTE antenna might also have the same problem. I had no...
I choose one NRF52 DK(nrf52840_pca10056) for my daily development. After hundreds of erase and write cycles, the DK won't behaves like it should do. The other DKs runs well...
Hi,
In the registery definition of nRF52840 it is stated for PSEL.TXD:
Reg ID: A -> from bit 0 til 4 for Pin selection
Reg ID: B -> bit 5 for Port number
In this case...
I am looking into interfacing a SD card to the nRF52840. I have used the FatFS example and that is working ok with SPI. Then I have looked at the QSPI example and that also...
