Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi,
I am using nRF51822QFAA-R7 controller(DC DC setup) in my design.
I am generating +3.3V from rechargeable battery and providing +3.3V as a supply to drive these controller...
Hi,
I'm just getting started with nRF mesh (sdk V3.00) and I've built the light switch sample successfully and deployed it on three nRF52832 development boards but provision...
hello,nordic
I use NRF52840 QSPI+FatFs+USB-msc(..\nRF5_SDK_15.2.0_9412b96\nRF5_SDK_15.2.0_9412b96\examples\peripheral\usbd_msc),I found there is a bug about write to flash...
I am working on a new design for the nRF52832. I need to match an antenna to the device. My understanding is that the output impedance of the nRF52832 is 53 + J66 for best...
I am unable to toggle LED's on server boards, using Push buttons on client boards. flashed the light_switch client,server, provisioning images on nrf52832 boards using nrf5SDKforMeshv300src...
I programmed my nRF9160DK with the asset_tracker app using SEGGER Embedded Studio for ARM.
What I did was to open the prj.conf file and changed the following from "n" to...
Hi all,
I'm currently testing my Mesh network on a small scale. I'm sending messages every 25ms with different TTL values in an environment as visualised below.
The...
Hello,
I'm currently using an nRF9160 DK v.0.7.0 and the provided samples like the asset tracker and the at command client. Compiling, flashing etc. of the firmware already...
Dear Sir/Madam,
Can nRF Sniffer fetch the data of BT Classic Devices having any BT Version from BT 2.1 to BT 5.0?
Kindly help me on this issue
Regards,
MIHIR TAIL...
(running a mesh 2.1 sdk)
I am provisioning my nodes over serial and do not need the GATT Provisioning service. I need to access the GATT Proxy service to send mesh data...
I want to upgrade FW.
Android app has done. but only iOS encounter some problems.
First, I try to download nRF Toolbox on Github. result is DFU Service not found .
I...
Hi,
As per subject I am looking to implement hardware on-the-fly AES-CCM encryption/decryption of ESB packets. Are there any examples/guides available for the nRF52840?...
Hi,
With the PPK PCA63511 we have tried different PPK software such as python 1.1, nRF connect for desktop.
In that process we observed that current measurements are...
Hi. I have a problem with using RS485 (ISO-3082DWR) from NRF-52832. The SDK version uses 15.02. Here's the code I've run. nrfx_uart_config_t uart_config =
{ .pseltxd = 30...
