Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
I have two questions.
Is it possible to use the DAP[n]/DAB[n] registers without using Bluetooth 4.0?
If it is possible, then how? I searched all the sample...
I am starting with Nordic nRF51822 and I would like to know if do you have some samples for use with emIDE (I liked it because you don't have size limitation). And I had some...
I saw two different way to ini ble
1 ) BLE_STACK_HANDLER_INIT
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false);
err_code = softdevice_ble_evt_handler_set...
I'm right now getting uC to sleep WHEN THERE ARE NO ACI EVENTS I think I'm doing right, the uC sleeps but I'm not able to wake up despite the fact that RDYN is connceted to...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Using sdk5.2, and ble_bondmngr_bonded_centrals_store() called on_disconnect, and then call
err_code = sd_ble_gatts_sys_attr_get(m_conn_handle,
m_central.sys_attr.sys_attr...
Hi!
I wonder what is the GPIOs nominal voltage level when I'm using the internal DC/DC converter?
I know that the internal DC/DC converter output voltage is 1,9V but I...
Hello,
we made PCB based on reference with ST balun. In circuit the low freq crystal is optional, so we didnt use it. In software i noticed app_timer use RTC timer. So the...
I am trying to bootload an extremely large hex file using a slightly modified DFU (modified from SDK v5.2.0's example)
The problem is that the hex is so large that eventually...
Im having errors like Arduino is in the while(1) loop if I enable the DC/DC converter in the characteristics and generate service.h file , If I do not use this setting everything...
I have a NRF24L01 board, which acts as a receiver. It listens on RF channel 2 using address pipe 0 address as follows 0xC47B4D0331. I am able to transmit to this NRF24L01...
I need to wake my uC from sleep when the nrf8001 gets in connected mode and for that I need to supply an external interrupt on hardware interrupts on the MCU.
Will active...
www.dropbox.com/.../error.jpg
it is not even reach main()
same as devzone.nordicsemi.com/.../nrf51422-flashes-ok,-but-debugging-fails-stays-in-moves-r0,r0
is it related...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
