Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
I have a custom hardware, with an external 128MB QSPI flash memory connected to a nRF5340. My current task at hand, is to store firmware update images for MCUBoot...
If I am having a custom board created and assembled using a pcb maker (makerpcb, jlcpcb, or pcbway) what do I need to ensure is on the board so I can flash and debug it? I...
We have a issue about nRF9161 on our custom board.
we flash hex our board. It doesn't work very well. sometimess it work and consume about 90mA current. sometimes board...
In our project we use a SHT4x sensor connected to I2C bus of nRF5340. To lower power consumption during idle/sleep we've a power line switch to disconnect the SHT4x from the...
Hi Nordic team,
I was testing whether Zephyr's LLEXT would work on the nRF52840DK. The example can be compiled on NCS 2.7.0 and loads fine. However the final step of having...
I am working w/ the nRF5340DK, and the project mentioned here (NCS v2.5.0, nrf/samples/crypto/rng). I was able to build/flash the project.
I wanted to verify whether the...
Hi,
I am getting to grips with the device tree and when i add an over lay file to the project, the 'new' devices are flagged with the waring that theyre being over ridden...
Hi,
using nrfutil pkg to generate the settings.hex file for the DFU is exceptionally slow on my M2.
I'm using what I believe is the latest version
nrfutil 7.5.0 (063f665...
I have an i.MX8 arm linux system running an OS based on yocto, with an nrf52840 connected over USB. The linux system receives nrf52840 firmware as part of its OTA, and updates...
Hi there,
Currently, I'm working on a solution where I need to design a software UART through emulated GPIO pins for nrf52833.
The requirements are that, solution would...
Hi all.
hello everyone . I have a project on the nrf52840 board . The wiring of the board is shown below . The module is correctly flashed , but does not start . As if it...
Dear Support,
I was working on refactoring the project and changed a majority of cmake files to improve the architecture of the project but when I finished I found out that...
Hello. "zephyr/samples/drivers/adc/adc_dt" example sample added an additional adcpin.
When reading the sensor value connected to AIN0, the value of AIN1 is also changing...
When I used the code to get the RSSI values for different channels, I found that it was very time-consuming, about 400-500ms, and most of the time was spent waiting (NRF_RADIO...
Hi.
Please tell me if it is possible to realize such a connection scheme?
I want the Dongle to act as an intermediary for data transfer from the custom board to the smartphone...
