I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
From: https://github.com/zephyrproject-rtos/zephyr/issues/103807 Describe the bug
Hello,
I have configured a project based on the nRF5340 DK board and added a debounce...
Hi, So, I want to do BLE DFU from one nRF52 MCU to another nRF52 MCU. The start point for me was this:
put SMP server sample on one nrf52dk (this device is advertising...
Hi
I am using the ESB sample and want to use the RADIO_MODE_MODE_Nrf_250Kbit PHY, but I will get not support after requiring:
Can we still use 250 PHY in nRF54L15 ESB...
Hi,
After upgrading from NCS 2.5.2 to NCS 3.1.1, I get quite frequent MPSL assertion errors on a nRF52840. Can you shed some light into what this assertion error is about...
The datasheet list
A25, B12, B26, D2, F2, G1, H2, J31, K2, T2, AG31, as N.C.
I have not been able to read exactly what N.C. implies: It could be: "do not connect", "no...
Hello,
I am working a project that uses the NRF52840 dongle with BLE and UART to communicate to two separate devices while going through temperature cycles. I have not...
My device supports both Central and Peripheral roles. By default, it works in Peripheral mode. When the device connects in Peripheral mode, I want the following behavior:...
Hello Nordic team,
I am working on an nRF52840 project using nRF Connect SDK (Zephyr-based, v2.x / v3.x) and I would like to clarify the official support status of a specific...
Running doxygen nrfx.doxyfile
Per the README.md in C:\ncs\nrf-bm\v1.0.0\modules\hal\nordic\nrfx\doc fails.
See output below.
C:\> C:\apps\doxygen-1.16.1.windows.x64...
Hi there.
we have firmware that was running on nRF5340 MCU. we had decided to migrate to the nRF54H20 MCU because of flash size limitation. this MCU was announced with 2MB...
I am trying to connect to two reflectors and sound only from 1 device so far the connection and soundnig works well for first set of connection and after a disconnectio, the...
I am modifying the Qorvo UWB SDK to add BLE operations. I have posted a couple other topics about different issues..
I have ported my code to the latest Qorvo SDK, They...
With NCS 3.0 and the nRF54L15, even after applying patches, the power consumption anomaly can still be reproduced at the edge of the NFC range. The power consumption anomaly...
We are using zephyr's conn_mgr to manage the network connection. From what I can tell, if I have set CONFIG_NRF_MODEM_NET_IF=y and NRF_MODEM_LIB_NET_IF_CONNECTION__PERSISTENCE...
I want to try the tdm function on the nrf54lm20 dk.
But i have encountered problem in the first step.
I do not know how to add the tdm port and assign the pin.
Whin...
