I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello!
Our client encountered a problem in the development of Matter: the client wants to add or reduce endpoints dynamically during user usage after adding a cluster. Is...
how to create the nrf52840 mesh of more than 50 devices ?
I am using the chat sample for this mesh network but i am tested with the 12 boards but i am getting reply from...
Summary
I 'm experiencing a regression where my SKY66112-11 FEM (on a Fanstel BT840X module) no longer activates when using IEEE 802.15.4 in raw mode with NCS 3.1.1. The...
Hello Nordic Team,
I am writing to report an issue with random reboots on our custom board using the nRF54L15, developed with NCS v3.1.1 for a Matter device.
The reboot...
Hello,
I am building an application that need to have BLE with bonding enabled. It also need to save a moderate amount of data to a file system connected to a external flash...
Dear Nordic Support Team, I am currently performing Matter certification testing on our device based on the nRF54L15 using NCS v3.1.1 (Matter SDK 1.4.2). I am using the Matter...
Hi, support team,
I am conducting self-testing on a device developed with NCS 3.1.1, using the test versions corresponding to v2.13+summer2025 and Matter 1.4.2.
I...
Hello, Nordic Team! I am conducting Matter Test Harness testing and have successfully built the test environment. However, I am encountering some issues during test execution...
Using nrf5 SDK (not connect):
I have a RTC2_IRQHandler that is correctly being called.
rather than:
void RTC2_IRQHandler() {
if (mode == 2) {
handleMode2();
}...
Hello,
We are in the final stages of development and are trying to tune our device to perform its best in noisy environments:
We are using nRF52833 SOC as a central...
Hello,
We are using 2 nRF5340-based devices running:
samples/bluetooth/periodic_adv_rsp
samples/bluetooth/periodic_sync_rsp
with the PAwR configuration (modified...
I am evaluating the board nrf3054-dk + nrf7002-ek I build and run the sample project net/samples/wifi/shell on my board when I compiled the project, I added the following...
The blinky example from the official website can be programmed, but after opening the code and compiling with SES to generate the hex file, it cannot be programmed. An MBR...
I think variations on this question have been posted before but they all seem to be very old. I'd like to use the Bluetooth 5.2 LE Power Control features that involve exchanges...
