Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Dear Support Team，
Based on SDK15.3, nRF52832, follow the instructions to run the DFU process, use the mergehex.exe tool to merge settings, app, boot, and sd into one hex...
Hello everyone,
I currently using this lib: GitHub - Martinsbl/nrf5-mpu-examples to read data from MPU9255, when I'm using the easydma for accelerometer and gyros its work...
I am using the PSA library for the nRF340 and trying to use persistent keys.
It all works without persistent keys enabled, but if I add the following two lines to the prj...
Hi. I am trying to start programming our own development desk with modul ACN52840 (SoC nRF52840). I can provide schematic of development desk in private message if needed...
Hi,
I am develloping advertising configuration and would like to use the fast or slow advertising mode.
In the ble_advertising.h, it seems that the limit are an uint32_t...
Hi,
I am performing several "mlme_reset_req()" on a nrf52840 during runtime without problem, for the most part.
However sometimes the radio stack will stop after a ...
Good day
I noticed that the NFC tag reader sample is not compatible with the nrf9160K. Is there a reason for this ? will development be possible?
Thank you!
Hi Nordic
I downloaded nRF5340 DK Hardware files (Altium Designer files).
pca10095_sheet1 and pca10095_sheet2 can be imported in PADS logic tool.
But, files from sheet3...
Hello,
I have a problem when I send data with CDC ACM and using CLI interface my data is mixing. If I put a delay between sending data I have no problem but this solution...
Hi, I want to enter the NRF52 into a standby low power mode.
I am running sdk17.0.2, with FreeRTOS and softdevice (7.2)
The steps I take are:
1) stop all my threads...
I'm trying to integrate the following driver into my project
https://github.com/nobodyguy/HX711_zephyr_driver In order to load it I need to update the west manifest. Using...
Hello,
I am working with the nrf52840 chip, and would like to store a serial number on the device that persists across boots and OTA-DFU. I have integrated the nvs sample...
Dear All:
We run a simple message model in light_switch_client and light_switch_server code.
After provisioning the two nodes via nRFmesh app and set pubilsh in clent...
Hi,
We need to refer detailed documentation & implementation for health model struct bt_mesh_health_srv_cb
we referred to this document - https://docs.zephyrproject...
