Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
HI,
I start a scanning and print advertising report when address match on nrf5 SDK v16.0.0 with S140 on nrf52840. It goes well until I enable GNU extension in Keil. I don...
Hello. I have a project that needs an update.
The project was working before July 2022. However, now it doesn't work anymore (VsCode run/debug doesnt work) anymore. The...
Greetings,
during test of a device, we have tried uploading a shell sample in a nrf52840dk board. However for some reason this caused the board, or at least the installed...
Hi - I am using nRF5 SDK v17.1.0 and Segger Embedded Studio v6.34a. I am testing the ble_app_buttonless_dfu for pca10040_s132.
I am compiling ble_app_buttonless_dfu_pca10040_s132...
Dear Nordic Engineers
I would like to use the DFU trigger library to realize the NRF CONNECT for Desktop enter bootloader.
I found a demo in devzone: https://devzone...
Using a MAC running Monterey, VS code runs from command line on a terminal window from everywhere. When clicking on the "Open VS Code" button from the toolchain manager it...
For the nRF5xxxxx series, it looks like it has a differential ADC with 8 positive and 8 negative channels. It also looks like it has a scan mode where it will sequentially...
Hi,
I have a nrf9160DK and flashed it with Serial LTE Modem sample, however all the AT commands are just timing out.
Configuration is default and UART 0 is used.
...
Hi!
I want to connect my NRFL2401 to my computer using BLE (v4.0.0) in order to collect data from a sensor. However, the «Start Scan» button is not functional. When I click...
Hi!
I am trying to subscribe to nrf cloud with topic " prod/<TEAM_ID>/<DEVICE_ID>/jobs/rcv". After that I get Disconnect event in the MQTT handler.
Topic "prod/<TEAM_ID...
Hello Everyone,
I am using NRF52832 in my project and in my project I want to charge the device through USB C. So when we plug in USB C into the device, the NRF52832 should...
I followed the directions for pulling down the nRF Connect SDK v2.0.2 via Toolchain Manager v1.1.3 in nRF Connect for Desktop v3.11.1.
I am using Ubuntu 22.04.1 LTS 'Jammy...
Hi,
I am creating a central code from scratch, using zephyr version 2.0.1. I want to know the central code contain all the zephyr rtos property like thread in background...
Hi All,
I am trying to communicate with IC MAX17201 using I2C interface. I am able to detect the IC and communicate with it.
When I read 8bit registers from the IC I don...
Hello,
nRF5340, NCS2.0.2, vscode.
\v2.0.2\zephyr\samples\bluetooth\periodic_adv
when TX and RX work on PHY_1M, two side work well.
but when TX side set BT_LE_ADV_OPT_CODED...
