I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi
I have been using the nrf52840 development kit. In the sdk examples I am running the radio test example of pca10056, but in the retarget.c file I am getting this error...
Hi,
I'm working on a testbench to flash product with nRF5340 and nRF52840 chips.
In order to erase/flash both I'm using JLink Base compact and nrfutils CLI. But I have...
I've been trying to build the BLE Audio Broadcast source to run on my nRF5340 Audio DKs using the line in as the audio source. I've been developing on nRF52 for a while using...
Hi!
I need to create an application that sends text messages to a private server, such as ptsv3.com.
Could somebody please help me make this application work?
I encountered...
Dear Community,
I am currently working on an LTE-M and NB-IoT project in India using the nRF9151DK and testing the AWS IoT sample. Everything is set up, except for an active...
Hi, We are using following HW and peripherals: - nRF52840 - I2C - ADC - RTC1 - RTC2 - PWM - GPIO - SWI. We are using following 3rd party libraries: - nRF5 SDK v17.1.0 - FreeRTOS...
Hey All, I am sorry if this question may seem absurd or very very illogical, I am not very good at hardware but here I go. So I am designing a circuit around nRF54L15 as my...
Hi for the nRF54H20 the ds says there are two options for how to supply VDDH: either VDDH=2~5.5V with config 1 or VDDH=1.8V with config 2. If my system has 3.8V from a lithium...
Hello community,
I am trying for multiple firmware updates for my NRF5340 DK board.
What I am doing is I have build and flashed the SMP server sample program found /zephyr...
tl;dr: The clone would probably work more reliably if the nrf-toolchain-manager added the --depth 1 option, e.g.: git clone --branch v2.6.1 https://github.com/nrfconnect/sdk...
Hello Nordic Community,
I am working on a project using nRf5340DK and need to generate an 8MHz clock signal through a GPIO pin.
Could anyone provide guidance or share...
Hello everyone! :)
I'm having trouble detecting the sht85 sensor using the nrf9151dk. The wiring is good, since I tried connecting the sensor to the Arduino Uno and it works...
Dear Team,
I have a question regarding the Broadcast Isochronous Stream (BIS) / controller timing adjustments.
I am using the nRF52840 DK and NCS 2.9.
I have two devices...
Hello,
I try to understand how the NCS handle the 54L15 partition. When I turned on the mcuboot, I got this report and it is easy to understand:
However, when I use...
