Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
My project requires two sensors to operate on the same i2c bus, one of which is a display and the other of which is a touch sensor. And I have a problem where, if I test both...
Hi Everyone,
We are using nrf51824 for our project. As segger embedded studio has free license we have to migrate Keil project by following the article Segger Embedded Studio...
I have vsc version 1.66. I'm getting the following notification:
File changes watcher stopped unexpectedly. A reload of the window may enable the watcher again unless...
Hello,
I am using the https_client example for Thingy91. Everything was working fine until I tried to change the website to send https requests to (from example.com to google...
Hello Team Nordic, May I ask for your advice on how to build one nRF52840 to have two different UART connections to two different devices? May I ask for the any code examples...
Hi,
I am trying to integrate custom protobufs into the asset tracker project. I am referencing the zephyr/samples/modules/nanopb project for the same.
But I am getting...
HI ,
I'm trying to open terminal/command SDK v2.0.0 from toolchain manager (working with nrf connect for desktop v3.11.1) but it doesn't open.
while on SDK v1.9...
I'm just trying to make a simple communicatión between my nrf52 dk and my mobil using Serial Bluetooth Terminal app. I took the ble_app_uart example and I added a function...
Hi,
My project is a host micro (STM32) and a nRF52840 (controller mode) to implement a peripheral. My previous project (STM32 BLUENRG-M0 and host micro, HCI SPI interface...
Hi,
I'd like to add live audio streaming to my product, The current product consists of a sender unit and a receiver unit. Both using the nrf52833 (I've already bought 500...
hey guys i want to implement two separate application programs on the same chip.
Say Application1 is stored in address start_address1 to end_address2 and Application2 is...
Before using J-Link script to upgrade firmware, offsetStart (0x0) and offsetEnd (0x32E06) are correct. But after using J-Link script to upgrade firmware, offsetStart (0xADDEFE01...
Board: nRF52810
SoftDevice: s112
SDK version: 17.0.2
I'm trying to enable 2Mbps data rate. So I've added The following code in both peripheral and central.
ble_gap_phys_t...
I try to create new application using worspace type but fail , if I use freestanding type is OK. I already downlad and install SDK 2.0 . What happen? Could someone help me...
Hello, I just wanted to throw in that for a hobby project I created a PWM audio driver, with which one can play back 8-bit audio data very easily. Since it may be useful for...
