Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I start a application from the demo central-uart with the NRF CONNECT SDK 1.9.1
I try to communication via the com.
but the first byte of the rx buffer is wrong,I did...
I am running the throughput sample project on sdk 1.9.0 using two nRF5340 dev kits and am getting a throughput of 197 kbps using 2M PHY, Data Length 251 and Interval of 7...
Since upgrading to SDK 17.1.0 i get the following warnings of a redundant redeclaration for SystemCoreClock, SystemInit() and SystemCoreClockUpdate() for nrf52810 and nrf52840...
How to upgrade the nRF52832 tag in OpenWRT+nRF52832 gateway
gateway(openwrt+nrf52832) |_____ nrf52832 tag1 |_____ nrf52832 tag2 |_____ nrf52832 tag3 |_____ nrf52832 tag4...
Hi,
I try to install nrfconnectsetup330ia32.exe on my Windows-10 x64 bit computer. The setup program hangs when the progress bar is at about 33%. It just sits there without...
I am currently working on Nrf52840DK board trying to run ble_uart_app. Designed my board and I used BT840 instead of Nrf52840DK . After, code in NRF52840DK is working but...
Using a Thingy!91 (v1.0.0 and v1.4.0, firmware 1.2.3, 1.2.7) I get sometimes (every couple of days) a ENETDOWN when sending data out. Before that ENETDOWN, the device was...
Hello,
I've been working with NRF52840 for a while now. Recently I decided to add extra options to your code so I went to the development kit for a quick test and debugging...
I cannot get the esb ptx sample to compile on NRF52833 device when using VS Code v1.64.2 running windows 10 64bit .
I've installed everything according to videos, and when...
I am developing a nRF52832 based project where I want to position people indoor using an smartband (where the nRF52832 is placed). I was planning to use beacons so I can change...
Hello,
I have a ported a project from Keil (uVision) to Segger Embedded Studio. Everything is compiling, but unfortunately I have a problem with the linker I cannot solve...
Hello,
I am looking for some advices for a personnal project.
I would like to be able to receive all BLE packets ( so all protocols (GATT, SM, LL) and not only GATT) that...
Hi Nordic team,
I have used the nRF5340 BLE Online Power Profiler extensively in the past for things like estimated event energy and estimated battery life. Do you have...
