Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I have an issue with DFU via USB CDC ACM.
I would like to update the firmware using open bootloader over USB without softdevice.
I already tried to follow the thread:...
Hello,
I have a firmware working perfect with nRF52832 DK and nRF52840 DK, using SES 5.40a.
Now I just upgraded SES to version 5.70a. With new SES version, each time I...
Hi,
we are getting during NB-IoT attach (full AT dialogue below) for some nRF9160 SIPs:
URC: +CNEC_ESM: 29,0 URC: +CNEC_EMM: 19 URC: +CEREG: 2,"B414","000F6E21",9,0,19...
Hello,
I follow up this documentation https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrf/ug_thingy91_gsg.html#updating-firmware-through-external-debug-probe...
I try to run asset_tracker and asset_tracker_v2 on nRF9160DK. I observed that the default cloud Host Name is Amazonaws.com, which is shown in autoconfig.h file. see the image...
I tried to debug Asset_tracker_v2. During step by step debug, the program navigate to that part which is not included .. see the image. Also, I want to know, little more:...
Hello Devzone Community,
My name is Ted, and I am some way along development of Zephyr based firmware, running on an nRF9160 based custom board. I'm looking to put the board...
Hi,
How can we prove that the A-GPS is working correctly? We have run an experiment where we have use a module with A-GPS and one without and they have very similar (and...
Setup -
1. Sample used - nrf/samples/nrf9160/lte_ble_gateway
2. Board used to build - nrf9160dk_nrf9160_ns
3. NCS version 1.9.1
Steps performed -
1. Built the...
Hello Everyone,
I am trying to implement one wire protocol for interfacing MAX17211 fuel guage IC with NRF52840. I wand to know if there is any one wire library or any example...
Hi,
Do you have a suggestion for a 2.4GHz chip antenna? I sent a board to Ketil for RF tuning but the meander antenna ended up as too short. We would like to avoid a separate...
Hi there, I have been always using the dev board BLE antenna for the nRF52832-QFAB.. but now i need to reduce much more the size of the board, so i need a much smaller antenna...
