Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I just install the NCS in toolchain manager, but after installation, only one toolchain folder is there,no zephry,no examples,
I'm going to play in VSCode.
what should...
I use nRF5340 DK as Central, iPhone as Peripheral.
I start a scan with no filters and in scan_filter_no_match() I check if RSSI is good enough "RSSI > -45" and initialize...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hello,
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0.2. I am trying to implement my firmware which will consume less current. I have implemented...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. Our custom board has a connection to nRF GPIO...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. We need to publish the JSON messages larger than...
Hi, I am developing my own application using the SDK v1.8.0 with Demo direction_finding_connectionless_rx. I notice that in the
cte_recv_cb callback function, the rssi...
Hello,
I am using nRF 52840 DK board and using nRF52SDK17.0.2. I am trying to advertise data in GAP with the name " IG_Last4CharMAC_RFL " for example " IG_4DA8_RFL " but...
hello,
NCS1.9.1, Windows10 X64,nRF5340-DK, nrfx_i2s
in file boards\nrf5340dk_nrf5340_cpuapp.overlay
i've i2s DAC model ,it must use 4 line(MCLK,SCLK,SDIN,LRCK)
but...
I am trying to get this example program https://github.com/ARMmbed/mbedtls/blob/mbedtls-2.11.0/programs/x509/cert_req.c (stripped out all the file handling stuff) to run on...
Hello,
I crated a custom peripheral for my application, I took the code from the Blinky example and i changed the service.
I set the FIRST_CONN_PARAMS_UPDATE_DELAY parameter...
I would like to be able to use 3 different USB descriptors.
1. CDC ACM
2. Mass Storage
3. Composite device with CDC ACM and Mass Storage
These should be selectable...
Hi, Using windows 10 OS, and SES v5.40. I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK. I am using openthread protocol...
