i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi everyone, I have a problem when I configured custom board GPIO UART in NRF54L15. I know that the NRF54L15 have UARTE00, UARTE20-22, UARTE30. I just use 2 GPIO ( UARTE20...
I use the app_gpiote_user_register to set GPIO port 1 pin, but this registers only 32-bit mask, so it can only to setting port 0.
If I want to use the port 1 pin for app_qpiote...
Hi!
I'm attempting to run the application from this URL , but nothing appears on the serial console, and I don't see any posts on the toilet website.
Could you help me...
Hi,
I am using an nrf5340DK + nrf7002EK. i am able to run an example helloworld application with an immutable bootloader and mcuboot as platform bootloader. When i try to...
Hello! Recently while performing a BLE firmware update using the mcuMgr Library, the stages of the firmware update are as follows VALIDATE, RESET, and fail on UPLOAD. When...
the code below successfully complies and returns 3 services with 1 characteristic each, I have copied the uuid for the primary services and characteristic and that doesn't...
Our board is based on nRF52833, using SDK 2.1.2, Zephyr 3.1.99 Project is configured to enter low power mode for both CPU and peripherals CONFIG_PM=y CONFIG_PM_DEVICE=y Our...
Hi,
After downloading any of the projects from nordic github, how does one compile the project successfully? Where should i extract the files to and what paths should i...
HI.
NRF connect For Desktop Programmer program Fail.
So I used command Tool (nrfjprog). command Tool worked.
Enviroment:
- nRF Connect For Destop v5.1.0
- Programmer...
We're attempting to provision one of our nRF9160-based IoT devices to our AWS VPC.
We're following this procedure:
Provisioning our eDude on AWS
Step 1: Provision the...
I'm trying to get FOTA updates working on the NRF54L15 DK. I noticed there isn't a dedicated guide available for these yet so have been using this page: https://docs.nordicsemi...
I’m encountering a build issue with Zephyr (version 3.7.99) on my custom board based on the nRF52840 SoC. The build process fails during the linking stage with an undefined...
Hi ,
We are using MCU nRF52832-QFAA-R (Flash 512KB & RAM 64KB) with softdevice s132 - 6.0.0.
I am not sure what is extracly Soc Revision of the MCU ? But I read some information...
I have a custom SMP handler that uses an SPI transport. If I use the pin reset to reset the module after programming sometimes the module hangs when calling that handler....
