Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi iBasis support,
I'm having a billing issue with your website. I'm using the iBasis card with the NRF9160DK board.
When I ran out of data, I just follow the link on...
Right now I use the app_timer_cnt_get() method to get a current tick count. It appears to return a counter that increases with 32768 counts per second. However, it overflows...
Hi,
In NRF52832 i have integrated IMU sensor and and DPS sensor . i have build code and Run .
But after 2-3 minutes its stucked . so then i pressed the pause button ....
Hi, all
My custom board has nRF52833 mcu and wifi module(esp-wroom-02). I'm going to communicate with these two using the uart port.
The problem is, data communication...
Hi there, I am working with an application that uses the NRF51 chip (through the Taiyo Yuden EYSGCNZWY BLE module) and am trying to implement buttonless DFU. I am having issues...
In the latest release v1.8.0, there is an example ( Mesh and peripheral coexistence) which also has th e extended advertising.
However, it seems that the BLE Mesh stack...
Hello
I'm using multiple nRF52840-dk (SDK17.1.0, Windows, Segger, S140).
I'm trying to make BLE device(nRF52840-dk) that automatically connects to specific BLE device...
Hello,
I am using nRF5340 Audio DK devices. I am programming two (2) devices as 'Gateways' and one (1) device as a 'Headset'. I have two questions related to this matter...
Hi,
My project (under embedded studio )works if running on a chip with the register FICR INFO.VARIANT = 0x41414330
but freeze on a chip with the register FICR INFO.VARIANT...
I can't flash/write my nrf52840 Dongle under Linux with nRFConnect v3.9.1 with Programmer v2.0.1
The buttons remain greyed out, the left window does not display any information...
I'm following the heart rate sensor example in the VS Code Youtube Tutorials series, and there are some pretty straightforward prinkt statements in main.c, such as 'Bluetooth...
I'm getting data from peripherals, and I need 96KB/S to get to the NET layer, because the other side needs to use data in real time, but the data transfer is too slow.
So...
I have been working with multi-sensor example of ZigBee to develop it in zephyr. every things went well of endpoint sensor except that the coordinator suppose to receive the...
Hi,
I am facing issue at ble_stack_init() which internally calls sd_softdevice_enable(). I get NRF_ERROR_SVC_HANDLER_MISSING at sd_softdevice_enable() return value.
...
