Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello everyone,
I used the Multirole example as base for my code. My target is to make a communication with two NRF52382. I changed the HRS (heart rate servide) to my custom...
Hi,
I am using the PCA10040 DK (v1.1.1) to measure the current consumption in sleep mode and the current is about 200 uA. (3V, DCDC Enable)
Following is the code, it...
I'm new to the nRF Connect software and I'm following the helpful "nRF Connect for VS Code" video series on YouTube to install it on my Windows 10 PC. Everything was going...
hi support team,
customer has one question about about sd_ble_gatts_hvx notify API, found that this data is not sent out immediately, but there is one connect interval...
HI,
i building nrf5_SDK_for_Mesh_v5.0.0_src got error undefined reference to `NRF_LOG_DEBUG'
nRF5_SDK_17.0.2_d674dde , DK10056 52840,
i put it the same dir and seted...
Hi,
I got the example github.com/.../nrf52-ble-multi-link-multi-role and I have added FreeRTOS to the example refer to ble_app_hrs_freertos in SDK v15.2.0 with S140 v6.1...
HI,engineers
i want Design a product，One to many device.
One 52840 is used as the transmitting station and 20 52840 are used as the earpiece (receiving 4KB/s audio)；1KByte...
Hi,
We are currently trying to flash the connectivity firmware on the nRF52840 USB dongle using the Bluetooth Low Energy application available on the nRF Connect application...
Hi, I am using MCP2515 lib from https://github.com/DejanBukovec/NRF5-SDK-MCP2515
So far example is working when i connect Jlink RTT viewer throughout the testing.
...
Hello everyone,
I am new to the Zephyr RTOS and this is my first project with the nrf9160, although i already worked with the nrf52832.
I am using a nrf9160_DK and for...
Hello Trouble you again I can receive the data in the test now! But only the first few bytes can be received!
#define PACKET_BASE_ADDRESS_LENGTH (4UL) //!< Packet base address...
Can the nRF52840 dongle be used to sniff/record BLE communications even if the recorded packets cannot be decrypted, or can it only record packets when decryption is possible...
Hi all,
I got thread cli working and now I tried to set up a thread network.
I built the sample for the nrf5340PDK with overlay-minimal-multiprotocol.conf and overlay...
I currently trying to get my DK connected to nRF Cloud, I am based out of Western US and I have already provisioned my SIM card. I followed the documentation instructions...
