Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I understand I'd be using 16MHz timer for this and it worked on Arduino nano.
I'm trying to measure the distance above with nRF52840 dongle.
Those two edges come in every...
Hi,
I'm working on an nRF5340 project using nRF Connect SDK v1.7.0 with VS Code. I started my project with the NUS example.
I've been able to customize the standard/legacy...
Hello everyone,
I'm dealing with mcumgr-cli to exchange commands between a host machine (running Ubuntu 20.04 LTS) and a NRF52833 DK running smp_svr sample. I'm using NCS...
I want to have a single device that can both transmit and receive beacon packets using nrf52832.
Project Idea
Need to identify RSSI level of beacons around a device while...
I'm having some difficulty understanding what the nRF53 datasheet is trying to tell us about the internal load capacitors and related items. We are using both the LFXO and...
Hi!
There are many questions regarding the high voltage mode of the nRF5340 already in this Q&A, but I don't see the answer to the question, how it is enabled programmatically...
Hello, is it possible to set gpio direction (input/output) from devicetree?
I haven't found any gpio flags to do this in the gpio.h located in dt-bindings folder.
Hi all. The current devices we are developing are made with NRF52832 based on the NRF SDK v16. We also plan to use the Wirepas stack. Initially, we want to implement support...
hi
i have developed my device,and it was work in customs,but there is some device cant work after work some times.we recall the device and discover the firmware was loseed...
Hello,
I have a question regarding GPIO setting during sleep mode.
nRF52832 is sleep and wake-up by GPIO state(Red in below picture).
When Red is high, nRF52832 go...
We are trying to implement errata 254, but I've run into a couple of questions. What's the correct test to see if the device needs the workaround for the errata? NRF_FICR...
Hi, I am using pc-ble-driver v4.1.4 combined with connectivity firmware compiled with s132 v6.1.1. My application is running on custom hardware with a cp210x serial to usb...
Hi, i made some research on the VMA323 sensor, how to get it to work with my Nrf5340dk but i didn't find any documentation is there any available documentation about this...
Hello sir,
I am using nrf52832 Dev board and write the value '1' through nrf connect app by enabling the notification enabled with case length one i.e (p_evt_write->len...
