Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
Excuse me:
1、The customer wants to use p0.21 pin as General purpose I/O，Can the reset circuit of p0.21 pin be removed？
2、The customer said that when a new nrf52832 chip...
Hi,
I want to add DFU over mesh and usbd into the client example.
I have faced an error of Multiple definitions of UARTE0_UART0_IRQHandler. I comment out the UARTE0_UART0_IRQHandler...
Hello,
i am currently trying to create a project that uses the NRF52840 board as a switch to control sylvania smart+ A19 filament light bulb.
However, i am unable to detect...
Hi,
I'm using NRF52840 in order to implement an application which will connect to a mobile device with PIN code (MITM). In addition - my app will be able to connect to a...
Hi everyone,
I'm using the nRF5340 board, nRF Connect SDK v1.5.0 and the nRF Connect app.
I am also using the example code "beacon" and all the data with integer format...
Hello,
I have been developing a serial C# application to work with the nrf52840 chip, initial development was done using the nrf52840 development kit which worked without...
Good morning,
I am using SDK 16.0.0 and nRF52832 uC. I have a project where I need to connect the uC to a CoAP IP. The only internet access it has is through an SoC developed...
Hi, Usually we set FLASH_START macro to indicate application start address, I do like to consult is't possible to change the FLASH_START from prebuild binary file without...
Excuse me:
PCA10095 cannot be download .hex on SES and nrf conncet programer,The figure below shows the problem downloaded on SES.How to solve tihis problem？
Hi, dear Nordic & all：
When I run libuarte example，I found a problem， I just set P0.14 to high at the begin of mian function, then I send data and test the example's function...
Hello,
I'm trying to develop an application sending GPS over HTTP requests.
I started from the "https client" and "agps" samples in the NRF Connect SDK: the single examples...
Hi,
I'm trying to build secure bootloader DFU(non_debug_version) for PCA10040 with the below mentioned prerequisites and I'm able to build the bootloader successfully...
Hello,
I am using nrf52832 chip and SDK 17.0.2 (Softdevice 7.2.0).
I set the MAC Address as random static as shown below (only relevant parts shown):
ble_gap_addr_t...
We are an educational institution and were hoping to use these in a class integrated with LabVIEW. When we load this up on a faculty desktop and run a simple program, it works...
