Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello,
I am using the nRF52832 in a design where I have to read long buffer (>255 bytes). Using "nrfx_twim_rx" keeps things reliable however with nrfx_twi_rx the transfer...
Hi,
Could you tell me what API you used to obtain the positions in your field in the webinar test using %NCELLMEAS? All APIs I can find requires cell id not physical cell...
Hi,
In our board, GPIO 0, 1 is connected to external oscillator(32.768KHZ).
And I wish to use this oscillator instead of local oscillator.
CLOCK_CONFIG_LF_SRC is already...
What is the difference of NRF9160-SICA-R and NRF9160-SIBA-B1A-R and NRF9160-SIAA-R ?
Would there be comparison table available of the difference between SICA, SIBA and SIAA...
Hi Team,
We are using the NRF52840 for our development purpose in BLE peripheral Mode. While connecting to the Central Device we observed the behavior, It is negotiating...
Hello, I want to ask a question. We have a project that needs OTA function. There are two Bluetooth devices A and B.
1. Both A and B are central_and_peripheral
2. A's...
I want to check for an RX timeout after sending a TX.
I am puzzled on how this comes about.
As best I can tell I have enabled TIMER3 for the timeout.
I have created...
I'm trying to create a user defined HCI command for nrf52840 over the Zephyr APIs to be used against Bluez stack on Linux.
I've enabled the CONFIG_BT_HCI_VS_EVT_USER=y....
Hello,
I am trying to accomplish sending a simple ON or OFF command to the coordinator. Is this possible to do?
I have a router device with these Clusters:
It...
I have been converting my TWI calls to be asynchronous by specifying a twi_handler, but my NRF52840 does not sleep during the TWI calls.
I use SDK15.3 and s140 softdevice...
So this is my understanding of the programming process of an external board using the DK.
Pins from table 1 here: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrf91_dk...
Hi,
I want to develop DFU using BLE. I have started with test image given in the example folder.
I have nrf52480 device , using S140 softdevice. I have followed these...
I am unable to see advertisement on the nrfconnect app, when using BLE_GAP_ADV_TYPE_CONNECTABLE_SCANNABLE_UNDIRECTED
However, when using BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0) as a central and Android device (Bluetooth 4.2) as an advertisement.
During development, I was wondering...
Greetings.
We've been developing a product that uses BLE Mesh. We are currently using the Waveshare nRF52840 Bluetooth 5.0 Evaluation Kit for prototyping purposes. As far...
