Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Dear Sir/Madam,
I have already developed an RF communication device with an NRF24L01+ device. And I want to migrate to nRF52833-QIAA-R. For that, I have the below questions...
I'm using RTC to wakeup every 500ms, I have Watchdog enabled but after a while (about half.. or an hour...) it will not wakeup anymore and watchdog will not reset.
I measured...
Hi, we programmed the nRF52840-DK with ble_app_hids_keyboard demo (s140) and tested with different BLE keys under a Linux PC. It worked. Tested the same configuration with...
Hi,
I have some code that normally uses nrf_crypto with the cc310 or cc310_bl backend. I was writing a unit test for this code which compiles and runs in Linux/WSL. Since...
Has anyone written a utility to dump the tables of contents (i.e. directory of files) and
an entire file with record keys:contents to a host operating system file to a file...
Hi,
I'm working on the bootloader part of a project. Using nrf Connect, the integrated MCUBoot bootloader, trying to figure out how all the parts fit together. Running into...
Hi,
As iOS developer, I'm facing a really strange issue : Using the nRF Connect app, I try to connect my BLE device, with success or not depending my iPhone/iPad configuration;...
Hi guys,
I am using the nRF52832 board on which I run the LPN example from BLE Mesh directory. I put there the code for measuring the temperature and now I want to save...
Hi ,
How do customers choose printf lib when they want to use floats on functions printf and scanf?
The customer wants to use floating points
However, the current printf...
I want to use nRF Connect v3.6.0 Programmer and Segger J-Link Ultra+ in order to program our board. I can connect to the J-Link but receive an error message:
The Segger...
Hi Nordic team
Current https_client example at sdk connect
Connect to server --> send http request to server --> Wait response from server
Can we receive packet from...
Hello,
After a long investigation I got to the conclusion that SPI master (spi3) has been broken in the SDK version 1.4.1.
It is working fine in V1.3.1
I have an application...
Hello,
I'm using SEGGER Embedded Studio 5.30a with NCS 1.4.99.
I'm trying the "hello_world" sample but when i want to run on the nRF5340DK i get the followings errors...
Hi,
I am using FDS for read and write the records with SDK17, My code is working fine but when I change the optimization level 2 for size then I am getting FDS_ERR_UNALIGNED_ADDR...
Hello everyone,
I'd like to perform a DFU through the USB port on my custom NRF9160 board (DFU over UART) using the NRF Connect Programmer App.
I already did the Firmware...
