I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello Nordic Taam:
I follow the WEB steps below
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_tz_v4.1.0%2Fthread_ot_performance_measurement.html
Software...
I'm designing a EEPROM type of memory using a SDCard. The write and read functions works fine, but the initialization does not work sometimes and it stays in a loop (because...
The size of flash of softdevice in the "s132_nrf51822_5.0.0_release-notes" is 0x23000 but atrually the size of the flash used by softdevice is 0x224A7, which I found when...
We are using nrf9160 as an LTE-M modem with the serial_lte_modem app running on it. Another chip (ESP32) communicates with it using AT commands and after a few minutes of...
Hi team,
I am working with nRF9160DK on NCS v1.3.2.
I am building the asset_tracker application and from my understanding when running running west build -b nrf9160dk_nrf9160ns...
Hi, I just got my Thingy:91 and I'm trying to run through the getting started guide. On the nRF Connector v3.6.0 app, it doesn't change from "no devices available" to "select...
Hi
I'm trying to develop a solution where I have a different button debounce value (i.e. one call, then another call to app_button_init(..)) depending which part of the...
Hi,
in other vendor LTE/NB IoT modem implementations there are cumulative counters showing sum of time in ms spent in TX, RX, SLEEP.
Together with actual TX power they...
HI
I had setup the toolchain as described but on building the blinky project and other projects i got the following error.
Creating solution blinky.emProject cmake -GNinja...
Hello,
We are working on the nRF52832.
I consider the low power mode , the DC/DC mode instead of the LVO mode. See datasheet.
In DCDC mode there is a coil and capacitor...
Hi,
I had done a python script using pynrfjprog, and use pyinstaller already created an .exe,and this .exe works well on Windows 10 system PC.
But when I run this .exe...
Hi Team,
I'm working on projects based on nRF5_SDK_17.0.2_d674dde with git.
Everytime new SDK released we've to migrate sdk and start over a new git repository and lose...
Hi,
Our plan is to develop a BLE device (GATT peripheral) and to have all the data coming from this device being encrypted. We want to use OOB pairing with NFC.
I read...
Hi,
while i was compile the ble_app_uart example i am getting an error - cannot create command input file '..\..\..\..\..\..\components\softdevice\s132\hex\main.__i'
i...
