Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi All,
I am working on fatfs example from sdk 12.2.0 on pca10040, nrf52 dk, nrf52832. And i did not change anything in the code but it seems that my sd card is not getting...
I started with the template app and added BLE services, and I'm continuing by adding a TWI sensor (I2C). I know there is a TWI_sensor example, but I already had some working...
Dear All,
I am working with nRF52840 product. According to my scenario i have 1central unit(master) and up to 19 peripheral unit(slave).
I downloaded SDK 15.3.0 ble_central...
Hello, I am evaluating ways to enter the DFU mode when application is corrupted (i.e. it does not reach the code for entering bootloader).
The documentation states that...
Hi
I'm working on a IoT solution with a small circular board, 26mm in diameter. I was suggested by Johanson to use the 2450AT18D0100 antenna and a lowpass filter designed...
Hi,
I am new to this nrf development, I have been working on the SDK 15.1 on the nrf52832, with softdevice 6.1. I found these examples in the SDK very helpful. I have to...
Hi,
I am planning to send an analog signal to the nrf52840 dongle pin and send it through bluetooth to mobile app. I am thinking of merging ble_app_rscs and saadc together...
The IP mode is IPv4.
1. The hostname resolves to IP address. The resolved IP address is correct (verified with a nslookup command separately).
2. setsockopt(fd, SOL_TLS...
I am implementing a serial transmitter using the nrf_serial library from the nRF5 SDK 15.3.0. The application is very similar to a serially addressable LED string.
My serial...
Hi,
i m using my custom nrf52832 beacon.For Battery power, i used accelerometer.i trying to change advertising interval for non connectable BLE device while accelerometer...
Now there is a project, nrf52840 uses SPI to communicate with other microcontrollers. Data is currently available, but it is suspected that each packet lacks a second byte...
Using the nRF52832 device with the S132-v3.0 soft-device (s132_nrf52_3.0.0_softdevice) and SDK version 12 (SDK120200F12) (Customized for our application, which includes use...
I am working on a ble nus pheripheral application on nrf52810 with sdk 15.2 and s112. currently I can connect to nrf52 with 4 mobile phone at same time and send&receive string...
I managed to set the UUID section on my own, but I'm having trouble reading and writing some data. I'm changing the on_write function in Ble_nus.c, but I can't get results...
Hello,
When debugging one of the projects, I encountered the situation of a frequent reset of the device during connection. A quick scan under the debugger helped show the...
