Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I would like to increase the length of read & write characteristic value to 29 bytes. I changed the NRF_SDH_BLE_GAP_DATA_LENGTH = 36 & NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Hi,
I try to build a simple BLE central device from nRF52840 dongle.
Using Nordic's nrf Connect desktop application I upload connectivity FW.
I want to replace nrf...
Hello,
To the nordic experts, please share your opinion or any suggestions are welcome in finding the feasibility of nRF52832 SOC in our product based on the information...
If I go into a power save management, can still set any digital GPIO as an output without consuming current.
Push-pull?
For example I connect the GPIO to the Gate-Mosfet...
Hi,
We are trying to implement an interface to sniff bluetooth data. We are using Linux with Ubuntu 18.04. Our code for other interfaces are written in Python 3.6. Naturally...
Hi,
I am trying to implement chacha20 stream cipher to encrypt plain text and decrypt it. In the nordic SDK example the chacha20-poly1305 authenticator implementation is...
Customer want to konw the IC edtion such the 51822qfaa-G3 or 51822qfaa-H2. we know these information marked in the IC surface , but it need to open the product house and look...
Hi Nordic,
I am trying to save data in flash taking as reference the fds example.
Fist time that the code runs: creating the record and initializinf it, everything...
Seen on ncs v1.0.0. Adding " CONFIG_NEWLIB_LIBC=y" to the prf.conf and building the event_manager sample will replicate the error
Workaround was to comment out static_assert...
I want to wake up nRF9160 by SMS.
What I want to do:
The nRF9160 usually sleeps to reduce power consumption, and only when it receives SMS it wakes up and send some data...
HI i have issue while running the buttonless dfu with my application
I am using nRF52832 SDK15.3 SES windows 10.
I have to run my application with buttonless DFU so. i...
Question - How to enter in DFU mode using open USB bootloader example on pca10056 ?
i tried writing nRF52840DK with examples-DFU-open_botloader-pca10056_usb and usb_debug...
hello,
I recently updated SES and got a new version of nrfSDK.
Secure_boot sample does not contain Cmake. In other SDKs on github secure_boot does not exist.
is...
What is the best way to filter info center results to match my project? I'm using SDK 1.5.1 for S132 and I think that is softdevice 6.0.0.
It would seem like a simple top...
