Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
When i am sending data packet from node a to node b why is b node relaying the message back and forth.It shudnt do that .
I just have 2 nodes in the current setup. Node...
I watched https://devzone.nordicsemi.com/f/nordic-q-a/33591/softdevice-s140-v6-0-0-how-to-set-the-channel-mask-for-different-channels
Does this work the same way in my situation...
I'm having a heck of a time getting the SAADC to just return one sample in a blocking manner using SDK 15.2.0
I'm pretty far along in developing a couple of nRF52840-based...
How many capture compares does each timer have on the nRF52810?
The documentation is conflicting. In the "Registers" section for the Timer peripheral in the data sheet it...
Some comparison charts I've seen from Nordic indicate that the standard is supported by nRF52840 only, but it is not clear if it can actually do it in the three bands specified...
Hello,
I have a peripheral based on SDK 9.0. I have tried to follow the peripheral proximity example to get bonding working with the app. The App is currently running in...
Hello,
Im new to the Nordic Ecosystem, and have been trying to set hardware uart with Nordic Thingy 52 with CP210x using the sdk13 uart example. I included the uart driver...
Hi Nordic,
I was porting Nordic freertos hrs example(13.0.0-1) to Nuttx system. I can do advertising, connection establishment and data transfer, but bonding failed. I...
Hi,
We are using development kit NRF51822 in our project ...so plz tell me which version of sdk do i need to use ..and also which version of keil do i need to use for this...
Hello,
I want to make a PWM signal that fires an interrupt at the end of the PWM period. I want to use two CC registers - one for the pulse width and one for the period...
Hi,
we developed design with nRF52840, but we have issues.
Propably we have solution for this issues, but we need test it and we need default hex file in nRF52840 for...
As it stands there is some confusion about licensing the DFU utility code in our systems we are concerned about licensing issues. We are compiling the python to an executable...
1.do I need to write a XX_client.c and XX_server.c myself ? is there a basic model that I can build on it ?
2.I need myself model to send a custom message, how to do that...
Experimental Dimming server example was working fine using SDK MESH3.0 in addition to SDK BT 15.2.
Following upgrade of the SDKs to MESH3.1 and BT15.3, the experimental...
Hi,
Does "ble_app_uart" project can print debug message from "UART" interface? How can I do this job?
PS. My UART Port is at P0.18 (TX) and P0.19(RX).
Thank you, ...
