I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am looking at routine 'spi_master_using_nrf_spi_mngr', I found "#define NRF_PWR_MGMT_CONFIG_FPU_SUPPORT_ENABLED 1 " in the sdk_config.h file. Is this part of the routine...
Based on this question I've assumed that it's possible to use nRF52832 for providing Bluetooth connectivity to an embedded Linux platform.
A quote from the github repo...
Hello.
I merge into embOS start project some peripheral example from Nordic like the Serial and spi ones. In the Start I chose the CMSIS one without a specific MCU and bring...
hi,
i am using sdk 14.2.0 multi-link central example,
my aim is to connect multiple sensors (up to 8 ble peripheral devices) with extended packet enabled.
sensors will...
Hello all,
I'm trying to connect to custom Board with nRF52840 controler.
nRFgo Studio (V:1.21.2.10) gives error "No device detected, or readback...".
I've also tried...
Hi there!
I have the following setup:
A Raspberry Pi 3 B and a nRF52840 Development Kit acting as a Border Router as described in the official documentation ;
Another...
Hi!
I would like to know if it is possible to use the nRF52840 to read a mifare classic 1k card?
If it is, is there an example for this?
Thanks!
Andreas
I am currently developing a code that will serve as my pulse sensor. I am now trying to write the code in VScode, for it is very appealing to me. The problem now arises with...
Hey
This is sumanth. I have worked on light switch example with server, client and mobile as provisioner. I would like to develop a mesh network where the server has to...
history: https://devzone.nordicsemi.com/f/nordic-q-a/44018/softdevice-invalid-memory-access-info-0x2/172932#172932
compiler: keil
To solve the hardfault issue (SOFTDEVICE...
Hi guys,
is it possible to print in blocking mode by request?
I tried to use a return value from SEGGER_RTT_printf(0, "some text\n"); but the value is always the same...
I have many nRF24LE1E chips that have a corrupted Info Page. I use the Dataman-48Pro2 programmer. I have read and saved the Info Page from a working chip but have not been...
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio
Softdevice S140 v6.1.0, Softdevice S132 v6.1.0
Two nRF52832 DK, One nRF52840 DK
Windows 10 Pro
Hi, is it possible...
