I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
We are evaluating the nRF54LM20B for an embedded audio classification application and are trying to determine whether the Axon NPU can meet our latency and energy targets...
Hello,
I encountered an issue when using BT_LE_ADV_OPT_CODED in the bt_le_adv_param options.
When I enable BT_LE_ADV_OPT_CODED , the device cannot be scanned by other...
I am currently developing a project using an nRF5340DK and a custom board. ---------------------------------------------
PC ---(SWD)--- IntMCU at nRF5340DK ---(SWD)--- nRF5340...
Hi,
We are trying to get an accurate estimation of energy consumption of LTE searches and data sessions.
We currently do this based on XMODEMSLEEP and CSCON notifications...
I'm a bit confused about configuration necessary for PAwR where a connection is initiated with AUX_CONNECT_REQ as in examples periodic_adv_conn/periodic_sync_conn. If I disable...
Hi, I’m seeing a build failure after enabling SQSPI in the device tree when building with MCUBoot on NCS v3.2.1 for nRF54L15. The build works fine without SQSPI, but once...
Hello,
Did anyone get nrf54L15 to work with a TFT display over SPI?
I have been using the 1.28" 240x240 gc9a01 in several projects with nrf52840 (both using the DK...
Hello,
Recently I designed a wireless keyboard with a nRF52840 as the main processor. I had the board reviewed by a friend and had it produced by JLCPCB. I have assembled...
I'm currently attempting to profile a non-rechargeable lithium battery on nPM PowerUP(2.2.3). When I start the profiling process, the charging stage is correctly skipped,...
We've designed our own board based on nRF9160 for main CPU w/ LTE and an nRF52 for BLE. Using BMP for debugging.
I've successfully run several boards through the production...
hi,
i'm learning this exercise and i got this build error.
i'm using nrf 9160dk so can anyone tell me what problem am i facing in build time error.
thanks
vivek
Not sure if this is an nRF Connect or VS Code or Zephyr or West or some combination of the above, but I'd like to configure the development environment (nRF Connect extension...
Hello Nordic,
I am currently evaluating the nPM2100 using the nPM2100 Evaluation Kit for a low-power embedded device powered by a CR123A primary lithium battery (Li-MnO...
Hi,
I am testing an eSIM card. I am able to read the ICCID (20 digits) using the following command:
AT%XICCID %XICCID: 8934014012215261620 OK
However, I don’t know how...
