Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
What will be the price of nrf52 chips compared to nrf51?
Will there be any cheaper version of nrf52 chips with limited capacbilities (e.g. less flash, ram)?
I was trying to setup a GNU toolchain on Windows and use the nrfjprog utility, but despite having installed the J-Link drivers (4.78), nRFGo Studio as well as the nRF51 SDK...
I cannot seem to get pstorage working using the S210 softdevice. I can get it to work using the S130. I was not able to find any info on pstorage using S210.
I used the...
Hi
I want to use the nRF51822 to do the BLE product.I have read the datasheet of nRF51822.I have some questions:
1、Can the I/O of nRF51822 support 4.5V~5V input?
...
Hi All,
My goal is to change the advertisement(when not "connected" to ble device) in every SPI Interrupt, depending on the data received i set corresponding data in advertisement...
In porting over my project from Keil to GCC using SDK 8.1.0 I can build and run just fine when I build with Keil but when I build with GCC and try to run sd_softdevice_enable...
Hi,
I trying to write an application with android for my nRF51822 device
I use Battery service example but every time i update battery level i need to request for changed...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
Hi,all.i want to run DTM on pca10028 develop board and connect it to my pc via USB (JLink CDC UART Port) on the board.My pc operation system is ubuntu10.4. what is the port...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,all. i run example.py(nAN34 document) on ubuntu10.4,then get an error:
./example.py:line 13:unexcept error near "(";
./example.py:line 13:'def main():'
what's wrong...
Hey there,
I am having issues downloading the SDK for the NRF52. It just goes to a blank part of the page. Is there a better way for me to get a hold of this SDK?
T...
So after reading some material it seems like I can pretty much define which pins are responsible for I2C communication. Is there any limitation to which pins I can set? Does...
Hello,
There are many anomalies in the NRF52 Revision Engineering A (QFAA-AA0, QFAA-AC0) .
This revision it is the current chip?
If so, do you know when there will...
I am trying to build the "Getting STarted" example app. I got it to work with Keil. Now trying Eclipse.
I got all the includes in the project set up and these all resolved...
