working with a nrf52833, soft device 140.
I am trying to setup a whitelist with a known addresses before I start scanning. I am calling the following code before my main...
HI,
I am using the NCS V2.9.0 ,nrf Desktop sample;
I want to mouse can pair 3 hosts, and i can select one of them connect and work;
I set CONFIG_BT_MAX_PAIRED=3 and...
I have a custom nRF52832 board with outputs on P0.07 P0.08 P0.09 P0.10 and I want to write to them. 7&8 are working ok but 9&10 are not.
Let me emphasise THE BOARD IS WORKING...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
Hi all,
I have a custom board build with an nRF9151. I'm able to connect on int with USB/UART, I can send and receive AT command. Right now I'd like to send certificat to...
I'm having trouble getting the I2C interface working on our nRF54L15-based prototypes. The initial config write to the device fails; specifically, in the twim driver (i2c_nrfx_twim...
Hi,
I have question about a project I'm running on nRF connect sdk 2.9.1.
I noticed that whenever an i2c sensor device device_init() is returning a value not equal...
Hi Team, I am trying to see the PaWR PDUs in wireshark sniffer. I am using example periodic_adv_rsp from NCS v2.9.0. I am referring to the link for exploring. How can I see...
Dear Nordic company,
I am writting to you in order to get some information about buffer sizes in your aplication. I think, I am bale to modify buffer size and maximum...
I am designing an application using the nPM1100 and I would like to know if I can use the VSYS as a power supply pin for my other circuit.
Is VSYS supplied by the battery...
In the nrf_sniffer_ble.sh script, the block that checks for an active virtual environment uses the following line:
if [ ! -z " $VIRTUAL_ENV "];
Notice that...
Previously, I compiled and downloaded the radio_test example into two DK boards.
I then used the CLI to set the parameters for each board one as TX one as RX
On setting...
1. Can we use SIM other than iBasis to use nrf cloud?
2. My SIM does not have a PUK. How to proceed without entering it.
3. We need SIM too kit document for nrf9161. ...
We are using the nrf52840-based module in our product.
This module is already certified with BT SIG.
Do we still need to certify our product with BT SIG certification...
Hi, As I am working on nRF5340dk and I am facing issues with flash memory. My application is exceeding the size of flash in nrf5340 (1MB flash). I want to move to nrf54 series...
This is a continuation of my previous thread ( Connections drop and don't come back (and "SoftDevice Controller ASSERT: 53, 296") ) (Case ID: 341823).
The project is a star...
Hello,
I am using Zephyr Toolchain v2.9.0 on an nRF9161 custom board . I have updated the modem firmware to mfw-nr+_nrf91x1_1.0.2 and flashed the board with the hello_dect...
Hi to you all. I have a question about how I can apply this mechanism in nRF52.
In modern TWS, it works like the phone or PC connects earbuds separately and sends and receives...
Hello, i'm having a problem with the satellite detection time when I start gnss search. When I start the search, for a while at first the satellites are not detected and then...
We are making a board with nrf9161 and nrf54L15 so that we have the GPS tracking facility and BLE . We wish to connect (send) other devices' data to this device (like temperature...
Hello,
I am testing the "peripheral_hids_keyboard" sample from the Nordic Connect SDK v2.9.0 using the corresponding toolchain version. When connecting the device to an...
After I added the device on the Samsung platform, I shared the QR code, and then added it with Apple, but the device could not be found.The log prompt is as follows:
