Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
IUsing the Master Control Panel application on my Android device to connect to my nRF51822 module (acting as the GATT server), I have implemented the Device Manager (v10 SDK...
I have successfully compiled BLE application using tutorials provided on nordic website.
but when I start doing debugging for better understanding find out that I can not...
Hey,
We got a problem when trying to figure out how to detect the custom services from Unity. We are trying to read data and afterwards to do some manipulations of objects...
I want send ble bond connection request from raspberry pi to nrf51882.
Can you please let me know which ble libraries I need to send central ble bond request to nrf51882...
Dear Nordic:
I try to use pca10040 DK and SDK is nRF52_SDK_0.9.2_dbc28c9.
Test nRF52_SDK_0.9.2_dbc28c9\examples\peripheral\UART the function work well on my DK.
I...
Hi
sdk : ncs v2.1.0
example : serial_lte_modem
I used the following command to test and found that sending the character "failed, how should I set it so that I can...
Hello,
I'm working on an application that uses the aws_iot_send function ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/libraries/networking/aws_iot.html...
How to make nRF Connect SDK submit to other code management servers (such as bitbucket,Not github), And continue to use Git to manage this code?
I will modify the content...
Hi all,
I recently installed the nRF Connect SDK and have had some success. Very snazzy.
I have seen some issues with the JLink on the DK resetting during firmware validation...
I cannot seem to get floating point supoort for printf/scranf
It works for LOG_INF
I have tried the following .conf settings:
CONFIG_NEWLIB_LIBC =y
CONFIG_NEWLIB_LIBC_FLOAT_PRINTF...
Hi All!
I am trying to program the external nrf9160 SOC using nrf9160 DK using the following connections. Before that, I tried the same connections to program the nrf52820...
When I set CONFIG_LOG=y, CONFIG_SERIAL=y in prj.conf, the UART streams out diagnostic message from my application code as expected, but I also get this endless I2C error message...
I am using NRF52832 for my project.
Refer the following Softdevice and SDK versions.
Softdevice: S132_2.0.0-7.alpha
SDK Version: 4.0.0-2.alpha
Question 1:...
I am using nRF Connect SDK 1.9.0 and the NRF52840.
When building samples/keys/hw_unique_key you get this warning:
----------------------------------------------------...
Hi,
My nRF52840 dongle which was working fine in the past doesn't seem to be responding properly. Is there anything I can do?
Some background:
1 - I have used it...
When we test the matter, we sometimes will meet commissioning accessory fail and network dropping. In the worst case, we can't access the network for a long time after the...
NRF_SO_RAI_NO_DATA AT#XSOCKETOPT=1,50 does not cause RRC release as expected, instead hipower LTE continues another ~20s. https://github.com/nrfconnect/sdk-nrfxlib/blob/main...
nRF52840, SDK 17.0.2, SD140 v7.0.1
My firmware application is happily sleeping via calls to nrf_pwr_mgmt_run(), waking up to service interrupts and do work, then going...
I have not been able to get the nRF52840 ncs v2.0.2 watchdog not to reset.
I tried kicking the watchdog every second and can set a break point and see that the kick does...
