Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello,
IDE - Visual Studio Code
SDK version - 2.9.0
Computer platform - Win11
I'm at the early stages of a project which first requires to send ~10K of data to the...
I'm encountering a build error when compiling a project with both Wi-Fi and the PSA Driver for CryptoCell enabled in nRF Connect SDK v2.9.0. The error occurs in crypto_mbedtls_alt...
Hello,
When using extended advertising with coded PHY, the advertiser address is included by default in the auxiliary packet (AUX_ADV_IND) on the data channels and not in...
I ma supposed to read FA0A03048100020000F , BUT I END UP READING FA0A030482000202020202. This is also common with the peripheral i am trying to interact, It sends a packet...
Hi everyone,
I´m work on a project were i have to stablish a mqtt connection with a RabbitMQ broker thats have user/pass auth and tls without certificate validate. My...
Hello, The Online Profiler tool currently doesn't support the nRF 9151. Is there a possibility it will be supported in the future? In the meantime, if I choose the nRF 9160...
Hi,
I've been working on Nordic boards for almost a year now using Zephyr and nRFConnect. I've been able to understand the DevAcademy Courses and to reproduce them.
The...
Hi,
I am working with the nRF52 DK running the Blinky example , captured BLE packets using the nRF51 DK sniffer and analyzed the interval timings across the advertising...
Hello,
I've got the nrf9160dk board, but the nrf91 isn't visible. I was told that it's dead, and I should try to play around, at least with the 52840. I've tried to make...
Hello, I am currently working with VEML6035 light sensor and so far i had a hard time working with its 16-bit registers.
The code that i wrote:
overlay file:
I can...
Hi,
It seems like my system is crushing before going to deep sleep,
I have noticed that if I remove a k_sleep of 500 ms, just before going to deep sleep the system does...
It's successful when I use west :
% west flash -d build
But it's failed when I use nrfjprog :
% nrfjprog --program merged.hex --reset
OR
% nrfjprog -f unknown...
Hi nordic:
I use two NRF52DKs and download MESH CHAT separately, hoping to achieve communication between the two NRF52DKs:
SOFT VER: NCS2.8
The specific process is as...
Now I have a verification work on the nrf52840 development board, which is to verify whether the terminal device will perform signature verification after receiving OTA firmware...
