I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi all,
I am trying to use the bt_disable functionality on Adafruit Feather sense which has nrf52840 to restart a connectable BLE Service. The first call to bt_le_adv_start...
I'm developing an application using the NRF52840. I'm using the ADC, and there may be times where the signal to be measured is up to 1.8V, but the NRF52840 is not yet powered...
I am using the NRF52840-DK REV2 to program my custom board. I am using the debug out port and connecting it to my custom board, I tried both powering the custom board through...
Dear Nordic Engineers
I have a problem and would like to ask you about the I2C work state.
I read this link: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
Hi All,
I am working with NRF beacon project currently, and I explored many other NRF connect SDK sample projects like, Ble peripheral, ibeacon etc. But I am unable to...
Hi,
I'm trying to implement FreeRTOS on nRF52832 using the S132 SoftDevice and SDK version 17.1.0.
This is meant to read multiple sensors at a configured frequency ...
Hello all,
I have managed to connect the BLE module, based on the nrf52820 via the SW (4 pins) to the nrf52dk and surprisingly programming works via the Segger EM !
Indeed...
Hi,
I would like to carry the full modem update. Based on nordic website I need at least 4MBytes of flash for doing a full modem update on the nRF9160:
https://developer...
I have two Windows PC’s with an installation of SEGGER Embedded Studio on each and a nrf52832 project.
With the project and the library on a USB memory key running the debugger...
Hello,
I developed a driver for communicating with the kx134-1211 accelerometer over SPI for the nrf5340-dk. The driver works when the following pins are configured for...
Hi,
I am using the nRF9160 in a datalogging product, logging environmental sensors and sending data via MQTT over a LPWAN network. Something that I have noticed for a...
My project uses ESB for communication. In our hardware design, nrf5340 + FEM is used. Nrf5340 uses two GPIO link FEM chips to switch between PA mode and LNA mode.
I use...
i want to consult a question：
for exzample:
1. i use timer[1] ,and start it.
2. set timer[1]->capture[1] = 1,the assumed value of cc[1] is 0x1000;
3.enable campare...
